防犯カメラ Axon Body 2のPDF クイック・スタート・マニュアルをオンラインで閲覧またはダウンロードできます。Axon Body 2 2 ページ。
Axon Body 2 にも: クイック・スタート・マニュアル (2 ページ), クイック・ヒント・マニュアル (6 ページ), クイック・スタート・マニュアル (2 ページ)
Axon Body 2 Quick Start Guide
English
Hardware
Axon Body 2
Camera
Axon Body 2 Wall Charger (not shown)
Read, understand, and follow all current instructions, warnings, and relevant Axon training materials before using any Axon system. The
most up-to-date warnings and instructions are available at www.axon.com.
Before using an Axon Body 2 camera, ensure it is fully charged, and connect it to Evidence.com via the Axon Dock or Evidence Sync
software to ensure it is properly configured. See Battery LED and Recharging the Battery and Uploading Data for more information. If the
battery is removed or its charge is ever depleted, recharge and reconnect the camera again.
Recording
The Axon Body 2 camera has 2 operating modes. The default mode,
or BUFFERING mode, provides pre-event buffering to capture activities
that occur before you activate the EVENT (recording) mode.
1.
Turn the system on. Move the ON/OFF switch to the ON position.
• T
he camera takes a few seconds to boot up and be ready to record (the
red area under the switch will be exposed with the switch moved to the
ON position).
•
The operation LED will be solid red and then transition to blinking green
when the system goes into BUFFERING mode.
•
The Axon Body 2 camera will go into BUFFERING mode after the boot up
sequence. With default settings, the BUFFERING mode holds the previous
30 seconds of video (NO AUDIO) leading up to the beginning of a recording.
Camera Operation LED
The Axon Body 2 camera's operation LED displays the system's
current operating mode.
Operating Mode
Recording
Recovering interrupted video*
Buffering
Booting up/powering down
Error state**
*When the Function LED also is blinking red.
**When the Function LED also is solid red.
Axon Body 2 USB Cable
Solid Red
Blinking Green
Boot Up Mode
BUFFERING Mode
Operation LED
Blinking red
Blinking green
Solid red
Quick Reference
Function LED
Operation LED
Top View
Recharging/Dataport
Data Transfer & Recharging
through PC or Axon Dock
Camera Lens
Speaker
Battery LED
Green = 40% - 100%
Yellow = 20% - 39%
Red = Less Than 20%
Microphone
2.
To record, quickly double-press the EVENT button.
•
The camera now records audio as well as video.
•
The camera will beep twice to let you know that recording has started.
The two beeps will repeat every 2 minutes (audio notifications can be
deactivated if necessary).
•
The operation LED will blink red.
EVENT Button
3.
To add a marker to the video, quickly press and release the Function button.
4.
To stop audio recording (mute), press and hold the Function button for three
seconds.
5.
To stop all recording and return to BUFFERING mode, press and hold the
EVENT button for at least 3 seconds until there is a long, audible beep.
With default settings, the system does not capture audio in
BUFFERING mode, so anything recorded in that mode will be video-
only. BUFFERING mode starts only after the camera is turned on. The
system does not record when the Axon Body 2 camera is turned off.
Camera Function LED
The Axon Body 2 camera's function LED displays when certain
functions are enabled.
Function Enabled
Mute
Camera error ***
Bluetooth feature is booting up
***Use the power switch to turn the camera off and on.
Battery LED
The camera's battery LED displays the battery's remaining capacity,
when the device is being used or when charging.
Battery Capacity
Battery capacity is 40–100%
Battery capacity is 20–39%
Battery capacity is less than 20%
Battery critically low
Bottom View
Status LED
Power Switch
Red = On/Buffering
Function Button
Mute or add marker
EVENT Button
Double Tap = Start Record
Hold 3 Sec = Stop Record
Battery Status Button
Push to Show Status of
Battery
Blinking Red - EVENT Mode
Function LED
Blinking blue
Solid red
Solid blue
Battery LED
Green
Yellow
Red during operation; flashing red
and yellow during charging
Blinking red and yellow