- ページ 4

スイッチ 3Com Baseline 2816のPDF ユーザーマニュアルをオンラインで閲覧またはダウンロードできます。3Com Baseline 2816 9 ページ。 Baseline switches
3Com Baseline 2816 にも：製品マニュアル (13 ページ), データシート (2 ページ), データシート (2 ページ), データシート (2 ページ), データシート (4 ページ)

ページを印刷する

Connecting to a Network Device

Follow these guidelines to connect a device to the Switch:

Use Category 5 unshielded or shielded (screened) 100 Ohm

TP cable (or Category 3 cable for a 10 Mbps connection).

3Com recommends using Category 5E cable for 1000BASE-T

operation.

The maximum length of cable for each connection is

100 m (328 ft).

Connect one end of the cable to an RJ-45 port on the

Switch, and the other end to the appropriate RJ-45 port on

the connecting device.

Power Supply

Power problems can be the cause of serious failures and

downtime in your network. Ensure that the power input to your

OUNTING

Introduction

The Switch is supplied with two mounting brackets and four

screws. These are used for rack mounting the unit. When

mounting the unit, you should take note of the guidelines given

in "Positioning the Switch" on page 3.

Rack Mounting the Units

The Switch is 1U high and will fit a standard 19-inch rack.

CAUTION: Disconnect all cables from the unit before

continuing. Remove the self-adhesive pads from the

underside of the unit, if already fitted.

1 Place the unit the right way up on a hard, flat surface with

the front facing towards you.

2 Locate a mounting bracket over the mounting holes on one

side of the unit (refer to the figure following step 6).

ROBLEM

At frequent intervals you should visually check the Switch.

Regular checks can give you an early warning of a possible

failure; any problems can then be attended to when there will be

least effect on users.

Check that all external cabling connections are secure and that

no cables are pulled taut.

Refer to the information about LEDs given earlier in this guide to

see if the problem can be identified and solved. Here are some

common problems that can occur:

Activity Status LED not lit for a port that has a connection.

There is a problem with this connection. Check that:

The device being connected to is powered on and operating

correctly.

The cable is connected at both ends.

You are using a TP cable that is not damaged.

If the connection is to a workstation, that the workstation's

network interface card is installed and configured correctly.

NSTRUCTIONS

OLVING

system is clean and free from sags and surges to avoid

unforeseen network outages. 3Com recommends that you install

power conditioning, especially in areas prone to black outs,

power dips and electrical storms.

Powering Up

Use the following sequence to power up the Switch:

1 Check the network connections and cables.

2 Connect the power supply cable to the appropriate power

socket located on the rear panel of the unit.

3 Connect the plug to the power supply outlet socket and

switch on the power supply at the socket.

When the switch is powered on, the Power LED lights green. If it

does not, see reference 4 in "Features of the Switch" on page 3.

3 Insert the two screws supplied in the mounting kit and fully

tighten with a suitable screwdriver.

4 Repeat the two previous steps for the other side of the unit.

5 Insert the unit into the 19-inch rack and secure with suitable

screws (not provided).

6 Reconnect all cables.

All Activity LEDs appear to be lit continually. There may be

broadcast storms on the network. Remove port connections one

at a time, waiting a few seconds between each port. If the LEDs

go off after removing a port connection, the device that was

connected to that port is introducing an excessive amount of

broadcast frames to the network (some pieces of network

equipment operate by sending out broadcast frames regularly).

Refer to the documentation that accompanies the device for

information on disabling the broadcast operation.

If the problem persists and the unit still does not operate

successfully, contact your supplier with the following information

before returning the unit:

Product number and serial number (printed on a label

supplied with the unit)

A brief description of the fault condition