ベビーモニター Axvue E612のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Axvue E612 2 ページ。 Video baby monitor with 4.3'' lcd screen and two cameras

ページを印刷する

INSTRUCTION MANUAL

AXVUE E612 Video Baby Monitor

with 4.3'' LCD Screen and Two Cameras

Please read the following instructions and warnings carefully

Keep this instruction manual for future.

For technical support see FAQ page.

For adult use only.

FEATURES & COMPONENTS

Camera:

1. Power Indicator

6. Power On / Oﬀ Switch

2. Lens

7. Speaker

3. Nighttime LEDs

8. DC Jack

4. Microphone

9. Wall Mounting Hole

5. Temperature Sensor

Monitor:

× 1

Revised at 8/2020

Get to know us at: www.axvue.com

1. LED*

2. Power / Menu

3. Talk Back

4. Volume Up

5. Volume Down

6. Video On / Oﬀ

7. To Select a Camera / Up

8. Auto-scan / Down

9. Zoom / Left

10. VOX / Right

11. Microphone

12. Speaker

13. Battery Compartment

14. DC Jack

15. Kickstand

*LED

Power & Low Battery

Sound Lights

Adapters:

× 3

× 2

WARNING

THIS PRODUCT CAN NOT SUBSTITUE PARENT'S SUPERVISION ON YOUR CHILD.

Model- E612

- Store this product out of the reach of babies (at least 3 feets (0.9 m) away from the crib). A strap

wound around baby's neck may result in asphyxiation. Use safety clip to clamp the power cord and

keep it out of baby's reach. Do not use other extension cords. Only use the power adapter provided.

- Do not touch the exposed part if the adapter is connected with power.

- Test regularly before initial use or when change the position of camera.

- Avoid placing the product in humid place or contacting with liquid. (such as bathtub, sink, etc.)

- Do not apply heat to the product.(such as stoves, radiators, etc.)

- Using the product in ventilated place. Avoid placing it on sofas, cushions, beds or other places which

may block ventilation.

- The product only can be operated by adult. Do not allow baby to play with it. Tiny accessories are

contained, please be careful when unpack and install it.

BATTERY WARNING

- Only use the recommended rechargeable battery. Please contact with us if you need to change it.

For contact list, please refer to the last page of the instruction.

- Please clean the battery compartment before using.

- Avoid short circuit at power supply terminal.

- Remove the battery when you are not using it or when running out of power.

- Keep battery away from children.

- Dispose the empty battery properly.

WARNING

Asphyxiation Danger:

crib). A strap wound around baby's neck may result in asphyxiation. Use safety clip to clamp the power

cord and keep it out of baby's reach. Do not use other extension cords. Only use the power adapter

provided.

SETUP & USE

Please charge the battery for at least 8 hours

before using the product.

Step 1: Test reception ﬁrst, put camera in a suitable

place that will provide you the best view of your baby in

the crib (Note: Do not hang up the camera ﬁrmly until

initial installation test is completed). Plug adapter into

wall outlet and turn on the camera.

Step 2: Turn on monitor by pressing and holding Power /

button for 5 seconds until "axvue" shows up,

then video will show up on the screen immediately. If

video does not show up, please refer to "TO PAIR

MONITOR AND CAMERA (ADD CAMERA)" at next page. If

video shows up, the initial installation test is completed,

then you can set up the camera according to the

instruction below.

Set Up Camera: Place camera on a ﬂat surface, such as

wardrobe or shelf (Figure 1). Or hang it on the wall

(Figure 2). No matter wherever to place the camera,

please make sure to keep it away from the crib for at least

3 feet and all power cords should be placed behind the

camera properly. Then adjust the angle of camera lens

until the entire crib shows up on the display, or adjust it

to the best angle that you think to watch your baby.

TO USE PLUGGED-IN MODE

Step 1: Place the monitor display in living room, bedroom or any place you want to watch your baby.

Use adapter to connect camera with electrical outlet.

Step 2: Turn on monitor by pressing POWER/MENU

shows up on the screen.

Step 3: Press VIDEO ON/OFF

Step 4: Turn oﬀ the monitor completely by pressing and holding POWER/MENU

5 seconds.

TO USE PORTABLE / BATTERY MODE

Please charge the battery for 6 ~ 8 hours before using the product.

Step 1: Charge the battery for at least 8 hours before using portable / battery mode.

Step 2: Make sure the adapter is plugged into camera.

Step 3: The battery life can be up to 10 hours if it is fully charged.

Battery life will be shortened if recharging it continuously. Unplug the power adapter when you are

not using it for a long time.

TO PAIR MONITOR AND CAMERA (ADD CAMERA)

The monitor and camera are paired before shipment. If it is unpaired for some reason, please refer

to the following steps:

Step 1: Make sure the camera and monitor are in the same place.

Step 2:

Step 3:

Store this product out of the reach of babies (at least 3 feet away from the

button for 5 seconds until axvue logo or video

button to turn oﬀ the video if you only need to hear the voice.

Make sure the power adapter is plugged into

camera and turn on the camera by pressing Power

On/Oﬀ Switch "

" button for 5 seconds.

Signal

Figure 1

3 feet

Figure 2

button for

Turn on monitor by pressing

and holding POWER/MENU

button for 5 seconds.