- ページ 17

プリンター Epson 890N - FX B/W Dot-matrix PrinterのPDF 製品情報マニュアルをオンラインで閲覧またはダウンロードできます。Epson 890N - FX B/W Dot-matrix Printer 19 ページ。 Impact printers
Epson 890N - FX B/W Dot-matrix Printer にも：ユーザーマニュアル (48 ページ), マニュアル (11 ページ), 仕様 (2 ページ), 技術概要 (7 ページ)

ページを印刷する

Epson 890N - FX B/W Dot-matrix Printer 製品情報マニュアル

EPSON FX-890/FX-2190

Locking the Control Panel Buttons

You can restrict the use of buttons on the control panel using

Lock-out mode. In the default Lock-out mode, you can use

only the

Pause

Load/Eject

to change which functions are locked, see "Changing the

Lock-out Mode Settings" below.

Turning Lock-out Mode On and Off

1. Make sure the printer is turned off.

2. Turn on the printer while holding down the

and

buttons. The printer beeps twice, indicating that

Pause

Lock-out mode has been turned on.

When Lock-out mode is on, the Pause and Paper Out lights

flash three times when any locked button is pressed. To turn

Lock-out mode off, repeat steps 1 and 2. The printer beeps

once, to indicate that Lock-out mode has been turned off.

Changing the Lock-out Mode Settings

You can select which printer functions you want to be locked

while Lock-out mode is on (as described below). The following

table shows which functions you can lock and their default

settings (in Lock-out mode).

Function

Load

Eject

Tear Off

Bin

Micro Adjust

Font

Pitch

Pause

Reset

1. Make sure paper is loaded and the printer is turned off.

2. Turn on the printer while holding down the

buttons. The printer enters the Lock-out setting

Pause

mode and prints the instructions. (You'll need three sheets

of A4 or letter size single-sheet paper or three pages of

continuous paper that is at least 11 inches [279 mm] long

and 8.3 inches [210 mm] wide.)

16 - EPSON FX-890/FX-2190

and

buttons. If you want

Tear off

Load/Eject

Default setting

Unlocked

Locked

Unlocked

Locked

Unlocked

Locked

LF/FF

3. Follow the instructions to change the settings as desired.

4. Turn off the printer.

When you want to turn on Lock-out mode, follow the steps

above.

Aligning Vertical Lines in Your

Printout

If you notice that the vertical lines in your printout are not

properly aligned, you can use the printer's bidirectional

adjustment mode to correct this problem. During bidirectional

adjustment, the printer prints three sheets of alignment

patterns, labeled High Speed Draft, Draft, and NLQ (near

letter quality). You select the best alignment pattern from each

sheet.

To print the instruction sheet and alignment patterns, you need

four single sheets or four pages of continuous paper of at least

the following sizes:

Paper type

Continuous paper (including

perforated border)

Single sheet

If you use single sheets, you need to load a new sheet of paper

each time the printer ejects a printed sheet from the paper

guide.

Follow these steps to perform the bidirectional adjustment:

1. Make sure paper is loaded, then turn off the printer.

2. While holding down the

The printer enters the bidirectional adjustment mode and

then prints instructions and the first set of alignment

patterns.

3. As described in the instructions, compare the alignment

patterns and select the pattern with the best alignment.

Then select the pattern with the best alignment for each of

the remaining sets of alignment patterns.

4. After you select the best pattern in the final set of alignment

patterns, save your selection by pressing the

button. Then turn off the printer.

and

6/03

FX-890

FX-2190

9.5

11 inches

14.8

11 inches

(241

279 mm)

(376

279 mm)

A4 or letter size

A3 landscape

button, turn on the printer.

Pause

Tear Off/Bin