- ページ 17
プリンター Epson C11C524025 - FX 890 - PrinterのPDF 製品情報マニュアルをオンラインで閲覧またはダウンロードできます。Epson C11C524025 - FX 890 - Printer 19 ページ。 Impact printers
Epson C11C524025 - FX 890 - Printer にも： ユーザーマニュアル (48 ページ), マニュアル (11 ページ), 仕様 (2 ページ), 技術概要 (7 ページ)
ページを印刷する
EPSON FX-890/FX-2190
Locking the Control Panel Buttons
You can restrict the use of buttons on the control panel using
Lock-out mode. In the default Lock-out mode, you can use
only the
,
Pause
Load/Eject
to change which functions are locked, see "Changing the
Lock-out Mode Settings" below.
Turning Lock-out Mode On and Off
1. Make sure the printer is turned off.
2. Turn on the printer while holding down the
and
buttons. The printer beeps twice, indicating that
Pause
Lock-out mode has been turned on.
When Lock-out mode is on, the Pause and Paper Out lights
flash three times when any locked button is pressed. To turn
Lock-out mode off, repeat steps 1 and 2. The printer beeps
once, to indicate that Lock-out mode has been turned off.
Changing the Lock-out Mode Settings
You can select which printer functions you want to be locked
while Lock-out mode is on (as described below). The following
table shows which functions you can lock and their default
settings (in Lock-out mode).
Function
Load
Eject
LF
FF
Tear Off
Bin
Micro Adjust
Font
Pitch
Pause
Reset
Menu
1. Make sure paper is loaded and the printer is turned off.
2. Turn on the printer while holding down the
buttons. The printer enters the Lock-out setting
Pause
mode and prints the instructions. (You'll need three sheets
of A4 or letter size single-sheet paper or three pages of
continuous paper that is at least 11 inches [279 mm] long
and 8.3 inches [210 mm] wide.)
16 - EPSON FX-890/FX-2190
and
buttons. If you want
Tear off
Load/Eject
Default setting
Unlocked
Unlocked
Locked
Locked
Unlocked
Locked
Locked
Locked
Locked
Unlocked
Locked
Locked
LF/FF
3. Follow the instructions to change the settings as desired.
4. Turn off the printer.
When you want to turn on Lock-out mode, follow the steps
above.
Aligning Vertical Lines in Your
Printout
If you notice that the vertical lines in your printout are not
properly aligned, you can use the printer's bidirectional
adjustment mode to correct this problem. During bidirectional
adjustment, the printer prints three sheets of alignment
patterns, labeled High Speed Draft, Draft, and NLQ (near
letter quality). You select the best alignment pattern from each
sheet.
To print the instruction sheet and alignment patterns, you need
four single sheets or four pages of continuous paper of at least
the following sizes:
Paper type
Continuous paper (including
perforated border)
Single sheet
If you use single sheets, you need to load a new sheet of paper
each time the printer ejects a printed sheet from the paper
guide.
Follow these steps to perform the bidirectional adjustment:
1. Make sure paper is loaded, then turn off the printer.
2. While holding down the
The printer enters the bidirectional adjustment mode and
then prints instructions and the first set of alignment
patterns.
3. As described in the instructions, compare the alignment
patterns and select the pattern with the best alignment.
Then select the pattern with the best alignment for each of
the remaining sets of alignment patterns.
4. After you select the best pattern in the final set of alignment
patterns, save your selection by pressing the
button. Then turn off the printer.
and
6/03
FX-890
FX-2190
9.5
11 inches
14.8
11 inches
(241
279 mm)
(376
279 mm)
A4 or letter size
A3 landscape
button, turn on the printer.
Pause
Tear Off/Bin