- ページ 5

ロックス Digilock Australia DL880のPDF ユーザーマニュアルをオンラインで閲覧またはダウンロードできます。Digilock Australia DL880 6 ページ。 All-in-one lock

ページを印刷する

*System will automatically quit if no operating for more than 10 seconds.

*When Voltage ＜ 4.8 V, will automatic alarm everytime using, and it still can use for around 200 times,

Unlock will be delay if exceed 200 times under low voltage, be sure to replace the new battery in time.

Lock Maintenance and Preservation

4.1Daily maintenance and preservation

1)Please do not contact with corrosive substances, so as not to damage the lock protective cover, which

reduce the average polishing glossiness and uniformity.

2)Handle is the key part of the lock, and its flexibility directly affect the use of the lock, please do not

hanging objects on the handle.

3)If door deformation,it should adjust the door gusset plate location in time.As combination latch bolt

into the frame box of friction is too large, which cannot be fully extended.

4)Please use dry soft cloth to clean the fingerprint acquisition window as it is will be very dirty and

moisture after long time using.

5)Please replace the battery immediatelywhen comes with low voltage alarmto make sure under normal

use .When replace the battery, please pay attention to is the cathode of the battery.

6) Please safekeeping mechanical keys.

7)Please do not use hard, sharp objects score fingerprint acquisition window surface (including nails).

8)Every time when collecting fingerprints, fingers should hold steady and flat over fingerprint

recognizer .

9)When lock rotation is not flexible, or can't keep the correct position, should ask professionalworker

filling mechanical lubricating oil to lock body.

10)Lock body transmission parts should be oiling, which will transmission smoothly and effectly prolong

service life. Advising checking every half year or one year to make sure all screws are fastened.

11)During using, when not using smoothly,can put some small graphite powder in slot on the lock core or

pencil powder to ensure that key inserted smoothly. But don't add any other oil for lubrication to avoid

grease sticking billiard spring, lead to cannot turn to open locks.

4.2 Most common problems that you might encounter.

Question: 1 fingerprint/card verification success I, blue indicator but can not open the door?

Reasons: (1) Installation problem (2) Lock mechanical failure, a lock core broken or lock core not

installed well.

Excluded methods: ask professional worker to check & test

Question: 2 with the mechanical key can not open the door?

Reasons: (1) Mechanical locks damage (3)Lock core has been broken (4)Failure of clutch mechanical

Method: Correctly use mechanical keys; or let professionals inspection carefuly check and replace the

damaged parts.

Question: 3 validation fingerprint/card to open the door,if red indicator lights, buzzer "drops ~ ' 'short, can

not open the door?

Reasons: (1) Illegal fingerprint. (2) The fingerprint has been cancelled. (3)Deviation position of the valid

fingerprint is too big. (4) Fingerprints have been damaged .(5) Fingers are too dry, wet, cold (6) Force is

too hard, and fingerprint shape has been deformation when collectting fingerprints. (7) Force is too light,

and may not fully touch fingerprint acquisition window when collectting fingerprints.(8) Direct sunlight

affect the fingerprint image

Methods: Using effective fingerprints or change to using password or key to open the door. Revalidate

the fingerprint again in correct way to get a valid fingerprint by fully touch acquisition window center.

(suggested one user should register more than two fingerprints) or convert password or key to open the

door. Keep your fingers moisturizing, dry, warm to make your fingerprint valid to open the door.

Meanwhile, should using some opaque objects to cover acquisition window when using fingerprint to

open the door.

Problem: 4. Before turning, handle and main cylinder can not go into a fully play?

Reasons: (1) Before and after the lock oiling parts have dust or lock body connection did not connect

properly (2) World pole anti-theft locks is loosen .

Method: Should be checked by professionals.

Problem: 5. Verify the valid password or fingerprints, normal state, the motor doesn't work, can't open the

door?

Reasons: (1) Loose cables (2) Motor failure

Method: Should be checking and replace the damaged parts by professionals.

Question: 6. Buttons have no response?

Reasons: (1) Its battery runs out or is battery not properly installed(2) Input the wrong password three

times, automatic lock (3) Lock body connection wire is loosing

Method: Using an external power supply or mechanical key to check the battery;Operating keyboard

again after 15 mins; Checking by professionals with mechanical key .

Question: 7. Enter a valid password or verification effective fingerprint/card, motor rotation, normal idle

but can not open the door?

Reasons: (1)Handles can not returen when verify the fingerprints or password

fastening screws is loosing.

Method:Reset back handle, and enter a valid password or verification fingerprint again to test.Or

Checking by professionals

Question 8. Door lock often open and closed, unable to normal use?

Reasons (1) Problem of component of the clutch (2) Fixed square shaft fastening screws is loosing

Methods: Checking by professionals.

(2) Fixed square shaft