コントロールユニット Digiplex EVO ANC1のPDF インストールをオンラインで閲覧またはダウンロードできます。Digiplex EVO ANC1 2 ページ。 Annunciator module
ページを印刷するAnnunciator Module V1.1
(ANC1)
Instructions
ANC1-EI02
P
M
ROGRAMMING
ETHOD
To program the ANC1, you must enter the Module Programming Mode using any
keypad in the system. To do so:
[0]
1.
Press and hold the
key.
[
]
2.
Enter the
INSTALLER CODE
[4003]
3.
Enter section
.
4.
Enter the Annunciator's 8-digit
5.
Enter the 3-digit section you wish to program.
Program the ANC1 using the WinLoad Software or the control panel's Module
Broadcast feature. Refer to the Digiplex EVO Programming Guide for more
details.
*Note: The serial number is located on the module's PC Board.
Partition Assignment
Use this option to assign access to partitions. The ANC1 will only display the
status of events that occur in partitions that have been assigned. For example, if
zone 5 in partition 1 has been breached, but partition 1 is not assigned to the
ANC1, zone 5 will not be displayed. Keys
through 8 respectively*. To assign access to a partition, enable the option that
corresponds to the desired partition. Partitions 1 to 8 are enabled by default.
[1]
ON = Partition 1
[5]
ON = Partition 5
[2]
[6]
ON = Partition 2
ON = Partition 6
[3]
[7]
ON = Partition 3
ON = Partition 7
[4]
[8]
ON = Partition 4
ON = Partition 8
Beeper Mute Mode
[1]
Enable option
in section [002] to mute options
option to enable the use of options
Beep on System Trouble
Enable option [2] in section [002] to set the Annunciator to emit an intermittent
trouble beep* every three seconds. Troubles may be:
AC Failure
Battery Trouble
Aux. Current Limit
Bell Current limit
[1]
[002]
*Note: Option
in section
Beep on Communicator Trouble
[3]
[002]
Enable option
in section
I
NTRODUCTION
The Annunciator Module (ANC1) is a
status display device that is
connected to the control panel's four-
wire combus as a stand-alone
module or mounted on a keypad. Set
the ANC1 to display the status of up
to eight partitions, zones 1 to 48 or
zones 49 to 96.
LED F
EEDBACK
Slow flash* Zone Alarm
Fast flash
Zone Tamper
Flash System not ready
ON
System ready
*
LED flashes until the partition in alarm
is disarmed
.
[
]
*.
SERIAL NUMBER
Section [001] - Option [1] to [8]
[1]
to
[8]
represent partitions 1
Section [002] - Option [1]
[2]
[5]
to
. Disable the mute
[2]
[5].
to
This option is disabled by default.
Section [002] - Option [2]
Bell Absent
ROM Check Error
RAM Check Error
Clock loss
must be disabled.
Section [002] - Option [3]
to set the Annunciator to emit a beep* when
these troubles occur:
TLM1
Fail to Communicate 1
Fail to Communicate 2
[1]
[002]
*Note: Option
in section
Beep on Network/Module Trouble
[4]
[002]
Enable option
in section
these troubles occur:
Module Tamper
Module ROM Check Error
Module Fail to Communicate
Printer Trouble
Module AC Failure
Module Battery Failure
[1]
[002]
*Note: Option
in section
Zone Trouble
[5]
[002]
Enable option
in section
these troubles occur:
Zone Tamper
Low Battery on Wireless Device
Zone(s) affected by: communication, fire loop, or CleanMe™ trouble
[1]
[002]
*Note: Option
in section
The trouble beep will stop when the problem is resolved, or if you
[
]
press the
key from any keypad on the network. This applies to
TRBL
Section [002], options [2] to [5].
Status Display Mode
Enter a value between 000 and 005 in section [003] to set which status the
Annunciator will display.
000 = Partition Status (default)003 = Future Use
001 = Future Use
004 = Zones 01 to 48
002 = Future Use
005 = Zones 49 to 96
S
PECIFICATIONS
Input Voltage:
Typically 11-16Vdc
Compatibility:
EVO48, EVO192
DGP48, DGP848
DGP-NE96, EVO96
WinLoad V2.10 or higher
Current Consumption:
Min:15mA Typ:50mA Max:100mA
B
I
ANC1
EFORE
NSTALLING THE
Choose a position where you will mount the Annunciator either as a stand-alone
module unit (see "Mounting as a Stand-alone Module"), or mounted on a keypad
(see "Mounting to a Keypad"). Once the module is connected and programmed,
you can use one of three display labels to reflect the ANC1's status display.
Should the system require more than one display, you can "stack" up to three
ANC1s.
Do not remove the ANC1's guide clip (Figure 1) unless it is mounted as
a stand-alone module. This clip sets the distance between the ANC1
and the keypad or other Annunciators (if they are "stacked"). If the clip
is removed the ANC1's covers cannot be placed properly.
Mounting to a Keypad
1.
Connect one end of the wires to the Annunciator's network terminals. Do not
close the back and front covers until you have decided how you will set the
module.
2.
From the keypad's back plate, cut out section labelled "E" as shown in
Figure 2 on page 2.
3.
Loosen keypad's network terminal screws without disconnecting the wires.
4.
From the Annunciator's backplate, cut out section labelled "A" as shown in
Figure 1 on page 2.
Fail to Communicate 3
Fail to Communicate 4
Fail to Communicate PC
must be disabled.
Section [002] - Option [4]
to set the Annunciator to emit a beep* when
Module Supply Output
Missing Keypad
General Failure
Network Overload
Network Com. Error
Missing Module
must be disabled.
Section [002] - Option [5]
to set the Annunciator to emit a beep* when
must be disabled.
Section [003]