- ページ 19

電子レンジ Sharp Carousel R-380LのPDF サービスマニュアルをオンラインで閲覧またはダウンロードできます。Sharp Carousel R-380L 40 ページ。 Microwave oven

3. Detector Circuit of Absolute Humidity Sensor Circuit

This detector circuit is used to detect the output voltage of the absolute humidity circuit to allow the LSI to control sensor cooking of the unit. When the

unit is set in the sensor cooking mode, 16 seconds clearing cycle occurs than the detector circuit starts to function and the LSI observes the initial

voltage available at its AN6 terminal.With this voltage given, the switches SW1 to SW5 in the LSI are turned on in such a way as to change the resis-

tance values in parallel with R98 ~ R102. Changing the resistance values results in that there is the same potential at both F-3 terminal of the abso-

lute humidity sensor and AN5 terminal of the LSI. The voltage of AN6 terminal will indicate about -2.5V. This initial balancing is set up about 16

seconds after the unit is put in the Sensor Cooking mode. As the sensor cooking proceeds, the food is heated to generate moisture by which the

resistance balance of the bridge circuit is deviated to increase the voltage available at AN6 terminal of the LSI.

Then the LSI observes that voltage at AN6 terminal and compares it with its initial value, and when the comparison rate reaches the preset value

(fixed for each menu to be cooked), the LSI causes the unit to stop sensor cooking; thereafter, the unit goes in the next operationautomatically.When

the LSI starts to detect the initial voltage at AN6 terminal 16 seconds after the unit has been put in the Sensor Cooking mode, if it is not possible to

balance the bridge circuit due to disconnection of the absolute humidity sensor, ERROR will appear on the display and the cooking is stopped.

1)Absolute humidity sensor circuit

[3] SERVICING FOR TOUCH CONTROL PANEL

1. Precautions for Handling Electronic Components

This unit uses CMOS LSI in the integral part of the circuits.When handling these parts, the following precautions should be strictly followed. CMOS

LSI have extremely high impedance at its input and output terminals. For this reason, it is easily influenced by the surrounding high voltage power

source, static electricity charge in clothes, etc. and sometimes it is not fully protected by the built-in protection circuit.

In order to protect CMOS LSI.

1) When storing and transporting, thoroughly wrap them in aluminium foil. Also wrap all PW boards containing them in aluminium foil.

2) When soldering, ground the technician as shown in the figure and use grounded soldering iron and work table.

2. Servicing of Touch Control Panel

We describe the procedures to permit servicing of the touch control panel of the microwave oven and the precautions you must take when doing so.

To perform the servicing, power to the touch control panel is available either from the power line of the oven itself or from an external power source.

1. Servicing the touch control panel with power supply of the oven:

Operational

R 1

amplifier

Output

voltage

R 2

S : T hermis tor

open ves s el

R 3

C : T hermis tor

clos ed ves s el

620k

R98

R99

300k

R100

150k

R101

75k

R102

37.4k

C. Thermistor in

closed vessel

S. Thermistor in

open vessel

R97

15k

F-1

R96

F-3

3.57k

R94

8 7 6 5

1 2 3 4

4.7k

R91

R92

3.32k

R93

F-2

IC2

1.8k

360k

VA : -15V

VC : -5V

VA : -15V

9 – 2

Abs olute humidity vs ,

output voltage characteris tic

Abs olute humidity (g/m )

SW1

P40

SW2

P41

SW3

P42

SW4

P43

SW5

P44

AN5

LSI

(IC1)

R95

AN6

15k

D90

approx. 1M ohm

R380L(W)