- ページ 2

液晶テレビ Sharp 32BC4KのPDF クイック・スタート・マニュアルをオンラインで閲覧またはダウンロードできます。Sharp 32BC4K 2 ページ。
Sharp 32BC4K にも：取扱説明書クイックスタートセットアップマニュアル (2 ページ)

ページを印刷する

Setting up the TV set for the fi rst time

Fitting the stand

TV panel must be facing downwards.

For the stand installation, there is

one type of screw provided as shown

below.

To complete the stand installation you

will require a cross head screw driver.

Place the TV set on a ﬂ at and

clean surface with the panel facing

downwards to avoid damage.

Place the TV set on a ﬂ at and clean surface

with the panel facing downwards to avoid

4 x

damage.

Used for attaching the stand

to the TV set (fi g.2)

Connecting your set

1) Connect the TV to your power socket.

2) If you wish to use the TV to receive Freeview/Saorview channels, connect the RF input

from the TV to your outdoor Digital TV aerial. If you do not wish to receive Freeview/

Saorview, skip this step.

4 First time installation

Basic installation steps are shown below. These may vary slightly depending on model.

Introduction

When the set ﬁ rst turns on, it enters the First Time Installation

mode. This can be restarted by restoring the set to default settings

in the 'About TV' Menu.

Note: In home mode,

the TV will switch off

automatically after 4

hours in the event that

no buttons are pressed on

the TV or remote control.

(You can change this

by pressing the [MENU]

button and then selecting

Settings>Time>Auto

Standby)

Environment of Use

Home Mode: For normal use, by default it is set to a power saving mode

which reduces the energy used by up to 25% (by reducing the power to

the LED/LCD panel). This can be changed in the picture mode settings.

Default Source

Select the source which you use the most. If Digital TV (Freeview) is chosen,

then at the next step, the set will tune in and default to Digital TV (Freeview).

If one of the other sources is selected, then the set will not tune in at this

stage and default to that input. If it is required to tune the set in later, press

the [MENU] button and then select Settings>Channels

To obtain a copy of your Operating Instructions, please go to: www.umc-uk.co.uk/instruction-manuals/sharp

Back/Shortest

Front/Longest

When the stand feet are installed correctly the

stand feet will be longest at the front of the TV

and shortest at the back with the feet pointing

away from each other.

3 Powering On the TV

TV Control Stick

TV control stick

Switch on the television by pressing

the TV control stick located on the

TV set.

Languages

Select your preferred on-screen display language. This will change the language

in which the menus and associated information is displayed in. When set up has

been completed, to change this press the [MENU] button and then select Settings >

System Menu > Language

Network setup

You can connect the TV to your broadband router or wireless network in order

to take advantage of the Smart functions. If you connect the TV to your router

using an Ethernet cable (recommended) this step will be skipped.

Tune in Channels

Choose to install terrestrial channels now or later.

4 x

When the stand/feet are in the correct

position, secure the feet to the underside of

the TV set using 4 screws provided.

Remote Control: Installing Batteries

Insert the batteries supplied into the remote

control and press the standby button to power

on the TV.

Country Selection

Select the correct ﬂ ag for the country in which the set will be

used in. This will enable the set to correctly install the functions

applicable in the country of use.

Set Up Netﬂ ix

If you have a Netﬂ ix account, it can be set up on the television

here. Once set up and validated, the First Time Installation

returns to the next step.

Support Advice

Information regarding support is displayed for a little while.

Tuning continues and a progress bar is shown with the number of

channels found indicated below.

If you are picking up signals from more than one transmitter, you

will be requested to select your primary and secondary regions.

Wall Mounting the TV

1. Remove the four screws that are supplied

in the wall mounting holes.

2. The wall mount can now be easily

attached to the mounting holes on

the rear of the TV.

3. Install the wall mounting bracket to the

television as advised by the bracket

manufacturer.

The picture shows the use of spacers, which

are not applicable to all sets/installations.

Image for illustration only.

Connectivity

SCART

DIGITAL

ETHERNET

AUDIO OUT

OPTICAL

VIDEO/Y

Ethernet/LAN*

Network connection

SAT In

Digital Audio

Digital Optical Audio Output

RF in

HDMI 1

HDMI input

HDMI 3

HDMI 2

HDMI input (ARC)

Earphones

Audio shared for Video/Composite

L/R

HDMI input (ARC)

Service Input

and component/ YPbPr

Video Input (green) and HD input

Video/YPbPr

HD input (YPbPr)

CI card in

(Ypbpr)

SCART

SCART input

USB 2.0

* The Ethernet/LAN port is used for Freeview HD services and smart functions.

Satellite Input

RF / TV aerial input

HDMI input

Earphone input

Input is used only by service centres

Common interface module

USB port 2.0