セキュリティセンサー Fibergate 5041210 DynaRound RG Hatch Guard YellowのPDF 取付説明書をオンラインで閲覧またはダウンロードできます。Fibergate 5041210 DynaRound RG Hatch Guard Yellow 14 ページ。
ページを印刷するD
ynaRound™ Hatch Guard System Installation Instructions
Estimated Installation Time: 2 Man Crew, 60 - 90 Minutes
The DynaRound Hatch Guard System is designed to protect all rooftop hatch entry and exit points. This non-penetrating
system is easily installed and can be used both temporarily and preeminently depending on need. The FRP railings and
galvanized fittings ensure a long service life.
INSTALLATION INSTRUCTIONS ARE FOR:
PN 5041210 DynaRound RG Hatch Guard Yellow – Fits Hatches 30-36 inches x 30-54 inches
o
PN 5041310 DynaRound RG Hatch Guard Yellow – Fits Hatches 30-36 inches x 96-114 inches
o
PN 5041410 DynaRound RG Hatch Guard Yellow – Fits Hatches 42-48 inches x 42-60 inches
o
PN 5041212 DynaRound RG Hatch Guard Lt. Gray – Fits Hatches 30-36 inches x 30-54 inches
o
PN 5041312 DynaRound RG Hatch Guard Lt. Gray – Fits Hatches 30-36 inches x 96-114 inches
o
PN 5041412 DynaRound RG Hatch Guard Lt. Gray – Fits Hatches 42-48 inches x 42-60 inches
o
Drawings for each part number of yellow Hatch Guard are included at the end of these installation instructions. The drawings
for the Lt. Gray Hatch Guards are identical except for color.
TOOLS REQUIRED
5/16-inch Hex (Allen) Wrench
o
5/16-inch Hex Drive Socket (to fit torque wrench)
o
Torque wrench 5 – 50 lb-ft range (6.8 –67.6 N-m)
o
Socket Set with extensions – SAE (inches)
o
Open End Wrench Set – SAE (inches)
o
Marker or Pencil
o
25-foot tape measure
o
Blue (removable) thread locking compound
o
NOTE: Cuts and drilled holes must be sealed to maintain corrosion protection.
IMPORTANT
Read these instructions completely before attempting to install the DynaRound Hatch Guard. It is important to understand
the installation procedure thoroughly prior to beginning work. It is the installer's responsibility to carefully follow fabrication
and installation plans and instructions to ensure design performance characteristics of the DynaRound Hatch Guard. The
installer could be liable for claims that result from improper installation.
ASSEMBLY INSTRUCTIONS:
1.
Inspect and inventory all components of the Dynaround RG Hatch Guard and compare to the bill of materials listed on the first
page of the drawings to verify that all materials are available for installation. Contact Fibergrate at 1-800-427-4043 to report
missing material and obtain replacements.
2.
Read these instructions and study the drawings thoroughly before attempting to install the DynaRound RG Hatch Guard. Be
sure you are referring to the correct drawings for the Hatch Guard being installed.
3.
Inspect the hatch and surrounding roof area where the DynaRound RG Hatch Guard is to be installed. Remove any debris or
obstructions in the installation area and verify all field dimensions and conditions prior to assembling and installing the Hatch
Guard.
4.
It is recommended to assemble the Hatch Guard adjacent to the hatch, then lift it over the hatch and clamp the Hatch Guard
in place. Prepare a suitable assembly area adjacent to the hatch and protect the roof in that area following the roofing
manufacturer's recommendations
5.
While the components of the DynaRound RG Hatch Guard which contact the roof are designed not to damage roofing
materials, it is recommended that the roof manufacturers recommendations be followed for protecting the roofing material
from abrasion damage at any location where the Hatch Guard contacts the roof.
www.fibergrate.com | 800-527-4043
1