![Sharp CD-BH20 操作マニュアル](/uploads/products/server2/5045661/5045661.jpg)
- 1. Special Notes
- 2. Consumer Limited Warranty
- 3. Controls and Indicators
- 4. System Connection
- 5. Remote Control
- 6. General Control
- 7. Setting the Clock (Remote Control Only)
- 8. Listening to Bluetooth Enabled Devices
- 9. Listening to a CD or MP3 Disc
- 10. Listening to USB Mass Storage Device/Mp3 Player
- 11. Listening to the Radio
- 12. Timer and Sleep Operation (Remote Control Only)
- 13. Enhancing Your System
- 14. Troubleshooting Chart
- 15. Maintenance
- 16. Specifications
Listening to Bluetooth enabled devices (continued)
■ Listening to the sound
Check that:
The source device Bluetooth functionality is ON.
●
Pairing of this unit and the source device is completed.
●
Unit is in connected mode.
●
1
Press the
(ON/STANDBY) button to turn the power on.
2
Press the
button on the main unit or BLUETOOTH button
on the remote control to select Bluetooth function.
3
Start the Bluetooth connection from the Bluetooth audio source
device.
4
Press the BLUETOOTH / button.
Notes:
If the source device has an extra bass function or equalizer
●
function, set them to off to avoid sound distortion.
Notes:
Make the Bluetooth connection again if the source device is not
●
turned on, or its Bluetooth functionality is off or is in sleep mode.
The volume of this unit may not be controlled as intended de-
●
pending on the device.
Bluetooth operation buttons
Main unit
Remote
control
■ To disconnect the Bluetooth device
Perform any of the followings.
– Press PAIRING button until "Disconnected" appears on the display.
– Disconnect or turn off the Bluetooth connection on the audio source
device. Refer the operating manual supplied with the device.
– Turn off this unit.
■ Auto power on
During Bluetooth standby mode, the unit will automatically
power on when the Bluetooth connection is set up between
the main unit and your device.
Note:
This function is not applicable during Bluetooth standby
mode off.
Operation
Press the button to play or
pause.
Press the button to skip to next
track.
Press and hold to fast forward.
Press the button to skip to
previous track.
Press and hold to fast reverse.
■ Link to Bluetooth headphone
You can connect a set of Bluetooth headphones to this unit.
Before making the connection, check that:
● The Bluetooth headphone to be connected is in pairing
mode and within range.
1
Select a desired function to listen to, except for Blue-
tooth function.
2
Press and hold the HEADPHONE LINK button on the
remote control until "Headphone Link" appears on the
display.
3
Press ENTER button. "Searching" appears on the dis-
play.
4
After finish searching, the nearby devices' names will
be shown on the display. Press
desired device and then press ENTER button. "Con-
nected" appears on the display and Headphone Link
LED (green) lights up.
● If your device does not appear on the list, do the
following:
- Make sure the Bluetooth headphone is still in
pairing mode. Refer to the manual supplied with
it.
- Press
button.
- Repeat steps 2 - 4.
Notes:
● Connection to Bluetooth headphone is valid in all
function except Bluetooth.
● Bluetooth headphone connection will be terminated in
Bluetooth function.
● When connected with Headphone Link, speaker
output is muted.
● Volume can be controlled on both main unit and the
connected Bluetooth headphone separately.
To disconnect the Bluetooth headphone:
Turn off the Bluetooth mode on the connected Bluetooth
headphone. Refer to the manual supplied with it.
"Disconnected" appears and Headphone Link LED (green)
lights off.
To re-link with the previous headphone device:
The device must be in pairing mode and within range.
1
Press the HEADPHONE LINK button. "Headphone
Link" will be blinking depending on the last connection.
2
Within 5 seconds press the ENTER button. "Linking"
will be displayed. "Connected" appears if re-link pro-
cess is successful.
Note:
If "Not found" appears, repeat from step 1. Make sure that
the device to be connected is within range and in pairing
mode.
E-10
or
to select the