- ページ 32
ステレオシステム Sharp CD-DH790NHのPDF 操作マニュアルをオンラインで閲覧またはダウンロードできます。Sharp CD-DH790NH 34 ページ。 Mini component system
ページを印刷するTroubleshooting chart (continued)
■ USB
Symptom
● Device cannot be
detected.
● Playback does not
start.
● Wrong time display.
● Wrong file name
display.
■ iPod
Symptom
● No sound is produced.
No image appears on
the TV/monitor.
● iPod will not charge.
■ Condensation
Sudden temperature changes, storage or operation in an
extremely humid environment may cause condensation
inside the cabinet (CD pickup, etc.) or on the transmitter on
the remote control. Condensation can cause the unit to
malfunction. If this happens, leave the power on with no
disc in the unit until normal playback is possible (about 1
hour). Wipe off any condensation on the transmitter with a
soft cloth before operating the unit.
■ If problem occurs
When this product is subjected to strong external
interference
(mechanical
electricity, abnormal supply voltage due to lightning, etc.)
or if it is operated incorrectly, it may malfunction.
If such a problem occurs, do the following:
1
Set the unit to the stand-by mode and turn the power
on again.
2
If the unit is not restored in the previous operation,
unplug and plug in the unit again, and then turn the
power on.
Note:
If neither operation above restores the unit, clear all the
memory by resetting it.
Possible cause
● Is there any MP3/WMA
file available?
● Is the device properly
connected?
● Is it an MTP device?
● Does the device contain
AAC file only?
● Is it a copyright protected
WMA file?
● Is it a false MP3 file?
● Is Variable Bitrate file
being played back?
● Is the File Name written in
Chinese
or
Japanese
characters?
Possible cause
● The iPod is not playing.
● The iPod is not properly
connected to the unit.
● Is the AC power lead of the
unit plugged in?
● The video cable is not
properly connected.
● The TV/monitor's input
selection is not properly
set.
● Wrong iPod adaptor is
used.
● The iPod is not making full
contact with the iPod
connector.
● The main unit is in stand-
by mode.
● Using 3
rd
generation iPod.
shock,
excessive
■ Factory reset, clearing all memory
1
Press the ON/STAND-BY button to enter the power
stand-by mode.
2
Whilst pressing down the OPEN/CLOSE button, press
the ON/STAND-BY button until "ALL CLEAR" appears.
Caution:
This operation will erase all data stored in memory
including clock, timer settings, tuner preset, and CD
programme.
■ Before transporting the unit
Remove the iPod, USB memory device and disc from the
unit. Make sure there is no CD in the disc tray. Then, set
the unit to the power stand-by mode. Carrying the unit with
iPod or USB memory device left docked or discs left inside
can damage the unit.
■ Care of compact discs
Compact discs are fairly resistant to damage, however
mistracking can occur due to an accumulation of dirt on the
disc surface. Follow the guidelines below for maximum
enjoyment from your CD collection and player.
● Do not write on either side of the disc, particularly the
non-label side from which signals are read. Do not
mark this surface.
● Keep your discs away from direct sunlight, heat, and
excessive moisture.
● Always hold the CDs by the edges. Fingerprints, dirt, or
water on the CDs can cause noise or mistracking. If a
CD is dirty or does not play properly, clean it with a soft,
dry cloth, wiping straight out from the centre, along the
radius.
NO
Maintenance
static
■ Cleaning the cabinet
Periodically wipe the cabinet with a soft cloth and a diluted
soap solution, then with a dry cloth.
Caution:
● Do not use chemicals for cleaning (petrol, paint thinner,
etc.). It may damage the cabinet.
● Do not apply oil to the inside of the unit. It may cause
malfunctions.
E-23
ON/STAND-BY
ON/STAND-BY
YES
Correct