- ページ 2

煙警報器 Digital Home Systems DHS-SNS-SM-DHSのPDF クイック・インストール・マニュアルをオンラインで閲覧またはダウンロードできます。Digital Home Systems DHS-SNS-SM-DHS 2 ページ。 Z-wave smoke sensor
Digital Home Systems DHS-SNS-SM-DHS にも：クイック・インストール・マニュアル (2 ページ)

ページを印刷する

Installation

Mounting

Unlock the back bracket.

Use the designated holes on the back bracket to screw mount it in

desired location.

For optimal use, mount the Smoke Sensor on the ceiling.

Place one 9V battery into the Smoke Sensor.

Mount the Smoke Sensor onto the back bracket.

After a few seconds the Smoke Sensor is ready.

Inclusion/exclusion into a Z-Wave network

1. Make sure your Z-Wave controller is in the right operation mode

(include or exclude).

2. Press and hold the push button for at least 1 second and release to

start the inclusion or exclusion process (indication mode: Ready for

learn mode)

Operation

Manual control

Press and hold the push button for 1 second and release to reset the Z-

Wave Smoke Sensor. The indicator light will turn red and the Smoke Senor

will beep when it is triggered.

Security system test within Z-Wave network

To test the sensor connection with your Z-Wave home controller (e.g. Vera

3) press and hold the push button until the Smoke Sensor stops beeping

(about 4-5 sec) and check if your home controller has seen that the device

is triggered. To remove the triggered status, hold the push button for about

half a second (one or two beeps only). Now the indicator light should be

on. Press the push button once to turn it off.

Indication modes

The indicator gives various statuses of the device as follows:

1. Ready for learn mode: Indicator light blinks regularly.

2. Learning in progress (inclusion): Indicator light blinks 8 times.

3. Learning in progress (exclusion): Indicator light blinks 8 times.

4. Learning mode success: Indicator light is on for 1 second.

5. Learning mode failed: Indicator light blinks rapidly.

Supporting Command Classes

Basic Device Classs: BASIC_TYPE_ROUTING_SLAVE

Generic Device Class: GENERIC_TYPE_SENSOR_ALARM

Specific Device Class: SPECIFIC_TYPE_BASIC_ROUTING_SMOKE_SENSOR

Listening: TRUE, Z-Wave Lib: 4.51

Command Classes:71 85 80 72 30 86 84

Class:0×71 COMMAND_CLASS_ALARM

Class:0×85 COMMAND_CLASS_ASSOCIATION

Class:0×80 COMMAND_CLASS_BATTERY

Class:0×72 COMMAND_CLASS_MANUFACTURER_SPECIFIC

Class:0×30 COMMAND_CLASS_SENSOR_BINARY

Class:0×86 COMMAND_CLASS_VERSION

Class:0×84 COMMAND_CLASS_WAKE_UP

Troubleshooting

NOTE: Before including the product to your Z-Wave network it is advised

to perform the exclusion procedure to reset network settings.

Frequently Asked Questions

Q: I can't include my Z-Wave Smoke Sensor into my Z-Wave network,

what am I doing wrong?

A1. Check that your home controller is set to inclusion mode.0

A2. The Z-Wave Smoke Sensor may already be included in a different Z-

Wave network. Perform the exclusion procedure and then attempt to

include the Z-Wave Smoke Sensor again.

Q: Why doesn't the Z-Wave Smoke Sensor detect any smoke?

A1. The connection between your Z-Wave Smoke Sensor and home

controller may have been severed. Ensure that the smoke sensor is

within range of your home controller or a Z-Wave device capable of

acting as a repeater then exclude and re-include the smoke sensor into

your Z-Wave network.

2. The battery is almost empty, try replacing it.

Q: Why does the push button on the Z-Wave Smoke Sensor not work?

A: Check that Z-Wave Smoke Sensor's battery is new and properly

connected.

Q: Why does the indicator light not work?

A: Check that Z-Wave Smoke Sensor's battery is new and properly

connected. The indicator light will not work if there is no power supplied

to the Z-Wave Smoke Sensor.

This device is using a radio signal that passes through walls, windows

and doors. The range can be influenced by local conditions such as

large metal objects, house wiring, concrete, furniture, refrigerators,

microwaves and similar items. On average, the indoor range is

approximately 12- 30 meters.

Do not expose this product to excessive heat or moisture.

Prevent long term exposure to direct sunlight.

Do not attempt to repair this product. If the product is damaged or if

you are in doubt about the proper operation, take the product back to

the place of purchase.

Do not clean the product with any liquid.

Do not paint.