- ページ 25

オーブン Siemens HB.78.B seriesのPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Siemens HB.78.B series 44 ページ。

ページを印刷する

3Trouble shooting

I f a fault occurs, there is often a simple explanation.

T r o u b l e s h o o t i n g

Before calling the after-sales service, please refer to the

fault table and attempt to correct the fault yourself.

Rectifying faults yourself

You can often easily rectify technical faults with the

appliance yourself.

If a dish does not turn out exactly as you wanted, you

can find useful cooking tips and instructions at the end

of this instruction manual. ~ "Tested for you in our

cooking studio" on page 31

Fault

Possible

cause

The appliance is

Defective cir-

not working.

cuit breaker.

Power failure Check whether the kitchen light

The time is flash-

Power failure. Reset the time.

ing on the display.

The settings on

The child-

the appliance

proof lock is

cannot be config-

activated.

ured. A key sym-

bol has lit up on

the display or

†'"".

The appliance

door will not

door is locked

open. A key sym-

with the child-

bol has lit up on

proof lock.

the display.

The appliance

door will not

door is locked

open. A lock

by the clean-

symbol H has lit

ing function.

up on the display.

The appliance is

Demo mode

not heating. The

is activated.

colon is flashing

on the display. On

some appliances,

a š will also

appear on the dis-

play.

--------

Notes/remedy

Check the circuit breaker in the

fuse box.

or other kitchen appliances are

working.

Deactivate the childproof lock by

pressing and holding the button

with the key symbol for approx. 4

seconds.

Deactivate the childproof lock by

pressing and holding the button

with the key symbol for approx. 4

seconds.

The lock can be switched off in

the basic settings.

Wait until the cooking compart-

ment has cooled down and the

lock symbol H has gone out.

Briefly disconnect the appliance

from the mains (switch off the cir-

cuit breaker in the fuse box) and

then deactivate demo mode

within approx. 5 minutes by

changing the basic setting ™‚„

or ™› to ‹. ~ "Basic settings"

on page 17

Warning – Risk of electric shock!

Incorrect repairs are dangerous. Repairs may only be

carried out and damaged power cables replaced by

one of our trained after-sales technicians. If the

appliance is defective, unplug the appliance from the

mains or switch off the circuit breaker in the fuse box.

Contact the after-sales service.

Error messages on the display

If an error message with """ appears on the display,

e.g. "‹†-„ƒ, touch the v button. This will reset the

error message. Reset the time, if necessary.

If the fault was a one-off, you can continue to use your

appliance as normal. If the error message appears

again, call our after-sales service and quote the exact

error message and the E no. of your appliance.

~ "Customer service" on page 26

Maximum operating time

If you do not change the settings on your appliance for

several hours, the appliance will stop heating

automatically. This prevents unintentional continuous

operation.

When the maximum operating time is reached depends

on the various different settings that have been

configured on the appliance.

Maximum operating time reached

"‰ appears on the display.

Turn the function selector to the "Off" position. You can

configure new settings if required.

To prevent the appliance from switching off when

Tip:

you do not want it to, e.g. with an extremely long

cooking time, you should always set a cooking time.

The appliance will heat up until the set cooking time has

elapsed.

Replacing the bulb in the top of the cooking

compartment

If the cooking compartment light bulb fails, it must be

replaced. Heat-resistant, 25 watt, 230 V halogen bulbs

are available from the after-sales service or specialist

retailers.

When handling the halogen bulb, use a dry cloth. This

will increase the service life of the bulb. Only use these

bulbs.

Warning – Risk of electric shock!

When replacing the cooking compartment bulb, the

bulb socket contacts are live. Before replacing the bulb,

unplug the appliance from the mains or switch off the

circuit breaker in the fuse box.

Trouble shooting