- ページ 4
スイッチ Siemens SITRANS RD500のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Siemens SITRANS RD500 8 ページ。 Configuring sitrans rd500 for connection to multiranger with modbus rtu
Siemens SITRANS RD500 にも： 取扱説明書 (48 ページ), 取扱説明書 (8 ページ), 取扱説明書 (8 ページ), アプリケーション・マニュアル (6 ページ), マニュアル (11 ページ), 応用例 (9 ページ)
ページを印刷する
GENERAL SPECIFICATIONS
1. POWER: Derived from system backplane. (The module draws 170 mA max. load on
power input of RD500). Modules may be hot-swapped (replaced while powered
up).
2. LEDs:
STS - Status LED shows module condition.
IN1-IN8 - LEDs are lit when associated input is active.
ALM - Alarm LED is lit when an internal alarm condition exists.
3. MEMORY: Non-volatile memory retains all programmable parameters. RD500
also stores the parameters in order to reprogram modules that are replaced.
4. INPUTS: DIP switch selectable for sink or source
Maximum voltage: +30 VDC, reverse polarity protected
Off Voltage: < 1.2 Volts
On Voltage: > 3.8 Volts
Input Impedance: Source Mode 10K ohms; Sink Mode 20K ohms
Input Frequency*:
Filter switch on: 50 Hz
Filter switch off: 300 Hz
* Actual useable frequency limited by communication to external device.
5. OUTPUTS:
Form A Relay Output:
Type: N.O.
The following pairs of relays share the common terminal: 1&2, 3&4, 5&6
Current Rating by pair: 3 Amps @ 30 VDC / 125 VAC resistive
1/10 HP @ 125 VAC
Life Expectancy: 200,000 cycles at maximum load rating. (Decreasing load,
increasing cycle time, and use of surge suppression such as RC snubbers
increases life expectancy.)
6. ISOLATION LEVEL: 500 Vrms @ 50/60 Hz for 1 minute between the following:
Inputs
Outputs
RD500 Power Supply Input
7. COMMUNICATIONS: Provided by the RD500
8. ENVIRONMENTAL CONDITIONS:
Operating Temperature Range: 0 to +50°C
Storage Temperature Range: -40 to +85°C
Operating and Storage Humidity: 85% max relative humidity, non-condensing,
from 0 to +50°C
Vibration According to IEC 68-2-6: Operational 10 to 150 Hz, 0.075 mm
amplitude in X, Y, Z direction 1 g.
Shock According to IEC 68-2-27: Operational 25 g's (10 g's relay), 11 msec in 3
directions.
Altitude: Up to 2000 meters
+
24VDC
7ML19985MD01
BLOCK DIAGRAM
PORT 1
PROGRAMMING
A
PORT 2
COMMUNICATIONS
A
ISOLATED
PORT 3
ETHERNET
B
POWER
-
SUPPLY
A
RD500
SITRANS RD500
9. CERTIFICATIONS AND COMPLIANCES:
SAFETY
UL508, CSA C22.2 No. 14-M05, UL61010-1, CAN/CSA C22.2 No. 61010-1
LISTED by Und. Lab. Inc. to U.S. and Canadian safety standards
IEC 61010-1, EN 61010-1: Safety requirements for electrical equipment for
measurement, control, and laboratory use, Part 1.
ELECTROMAGNETIC COMPATIBILITY
Emissions and Immunity to EN 61326: 2006: Electrical Equipment for
Measurement, Control and Laboratory use.
Immunity to Industrial Locations:
Electrostatic discharge
Electromagnetic RF fields
Fast transients (burst)
I/O signal connectected to power
Surge
RF conducted interference
Emissions:
Emissions
Notes:
1. Criterion A: Normal operation within specified limits.
2. Criterion B: Temporary loss of performance from which the unit
self-recovers.
3. Power supplied from back plane via RD500 Module.
10. CONSTRUCTION: Case body is high impact plastic. For indoor use only.
Installation Category II, Pollution Degree 2.
11. CONNECTIONS: Removable wire clamp screw terminal blocks.
Wire Gage: 28-16 AWG terminal gage wire
Torque: 1.96-2.23 inch/lbs (0.22-0.25 N-m)
12. MOUNTING: Snaps on to standard DIN style top hat (T) profile mounting
rails according to EN50022 -35 x 7.5 and -35 x 15.
13. WEIGHT: 6.6 oz (187.1 g)
ISOLATED
ISOLATED
1
INPUTS
8
RELAY
OUTPUTS
E
F
POWER
SUPPLY
Module
EN 61000-4-2
Criterion B
4 kV contact discharge
8 kV air discharge
EN 61000-4-3
Criterion A
10 V/m
EN 61000-4-4
Criterion B
power
2 kV
I/O signal
1 kV
2 kV
EN 61000-4-5
Criterion B
power
1 kV L-L, 2 kV L-G
signal
1 kV
EN 61000-4-6
Criterion A
3 V/rms
EN 55011
Class A
1
COM
1,2
2
3
COM 3,4
4
5
COM 5,6
6
Page 2