- ページ 27

食器洗い機 Siemens dishwasherのPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Siemens dishwasher 31 ページ。 Dishwasher
Siemens dishwasher にも：取扱説明書 (29 ページ), 取扱説明書 (30 ページ), 取扱説明書 (30 ページ), 取扱説明書 (30 ページ), 取扱説明書 (28 ページ), 取扱説明書 (26 ページ), 取扱説明書 (28 ページ), 取扱説明書 (26 ページ), 取扱説明書 (28 ページ), 取扱説明書 (32 ページ), 取扱説明書 (28 ページ), 取扱説明書 (34 ページ), 取扱説明書 (34 ページ), 取扱説明書 (28 ページ), 取扱説明書 (34 ページ), 取扱説明書 (26 ページ), 取扱説明書 (40 ページ), 取扱説明書 (40 ページ), 取扱説明書 (24 ページ), 取扱説明書 (28 ページ), 取扱説明書 (28 ページ)

ページを印刷する

Fresh water connection

Using the enclosed parts, connect the

fresh water connection to the tap

according to the installation instructions.

Ensure that the fresh water connection is

not kinked, crushed or twisted.

When replacing the appliance, always

connect a new water supply hose to the

water supply. The old supply hose must

not be re-used.

Water pressure:

Minimum 0,05 MPa (0,5 bar) – maximum

1 MPa (10 bar).

If the water pressure is higher, install a

pressure reducing valve.

Flow rate:

Minimum of 10 litres per minute.

Water temperature:

We recommend that you use cold water.

If you do use hot water, the temperature

should not exceed 60 C.

Electrical connection

Connect the appliance only to 230 V

alternating current via a correctly installed

socket with protective conductor.

See rating plate for required fusing

The socket must be attached near the

dishwasher and be freely accessible.

The connection may be modified by an

electrician only.

Use only a residual-current-operated

circuit-breaker which features the

symbol. Only this circuit breaker

guarantees compliance with the currently

valid regulations.

Removing the appliance

It is essential, when removing the

appliance, to observe the following

sequence: First, disconnect the appliance

from the power supply.

Pull out the mains plug.

Turn off the water supply.

Disconnect the waste water and fresh

water connections.

Loosen the fastening screws under the

worktop. If fitted, remove the base panel.

Pull out the appliance, carefully pulling the

hose behind.

Transporting the dishwasher

Drain water from the dishwasher. Secure

all loose parts. The appliance should only

be transported in an upright position.

If the appliance is not kept upright

during transport, any water left inside

may seep into the control module and

cause subsequent errors with

programme functions.

The appliance must be drained in the

following sequence:

Turn on the tap.

Set main switch to ON.

Select the B programme. The

programme duration in minutes is

shown in the numerical display.

Close the door.

Wait for approximately 4 minutes.

Terminate the programme by

pressing A and C

simultaneously.

The time display changes to

Wait a further minute and then

switch the appliance off.

Turn off the tap.

Protection from freezing

temperatures

If the appliance is installed in a location

where there is a risk of freezing

temperatures (e.g. in a holiday home), all

water must be completely drained out of

the interior (see "Transporting the

dishwasher").

Turn OFF the tap, disconnect the supply

hose and allow to drain.