- ページ 2

プロジェクター Epson dreamio EMP-TW500のPDF セットアップマニュアルをオンラインで閲覧またはダウンロードできます。Epson dreamio EMP-TW500 2 ページ。 Dreamio home projector
Epson dreamio EMP-TW500 にも：操作マニュアル (36 ページ), 仕様 (2 ページ), ユーザーマニュアル (9 ページ)

ページを印刷する

Turning the power on and projecting images

If the lens cover has been installed, remove it.

Use the accessory power cable to connect the projector to

an electrical outlet.

Turn the power on for the signal source (for a video

source, press the [Play] button to start playback).

Turn the power on for the projector.

After a short period, the lamp will turn on and projection will

start.

The area around the control panel buttons and characters light when

the projector's power is turned on. This allows you to operate the

projector in a dark room.

This projector has a "Lock Setting" function for

preventing mis-operations.

To turn off the light around the control panel buttons

and characters, set "Button Illumination" to "OFF".

User's Guide: "Configuration Menu Functions"

This projector is provided with an Auto Setup function that

automatically adjusts images to the optimum quality when the

input signal from the connected computer is switched.

If a laptop computer or a computer with a LCD screen has been

connected to the projector, you may need to use keyboard or

function settings to change the output destination. While holding

down the

key, press

(the key with a symbol such as

on it). After the selection is made, projection will soon start.

Computer documentation

Signal source cannot be selected / Images

are not projected correctly

Do the input signal settings

match the projector settings?

If connected to the

[InputA] or [InputB] port

Are images being played

back by the signal source?

Has the VCR been connected

A connected signal

using an RGB SCART adapter?

source cannot be

Has the DVD been connected

selected.

using an RGB SCART adapter?

Adjusting the projection screen

Projection image position adjustment

(Lens shift)

Fine adjustments to

image size

(Zoom adjustment)

Left

Down

Right

Focus adjustment

Correcting projector tilt

If the projected images are tilted horizontally, use the front adjustable feet to adjust the projector

so that it is horizontal.

Extend

Turning the power off

Turn the power off for the signal sources that are connected to the projector.

Press

on the remote control or

projector.

If you press

, the message shown right will be

displayed, so press

again.

The

indicator will flash orange and the cool-down period will start.

You cannot use the remote control or the projector's control panel during cool-down

(takes approximately 30 seconds).

After cool-down is complete, the

indicator changes to steady orange and the

projector goes to standby mode.

If the projector is on a surface such as a tabletop, the surface of the table near the air

exhaust vent will become hot.

The

Light green (during projection)

Selecting image source

NEC

Panasonic

Toshiba

IBM

SONY

Fujitsu

Macintosh

If there is a problem with projection even though the projector is set up and connected correctly, check the following points.

If the following points fail to solve the problem, refer to

Press

in accordance with

the video input source and select the format

that matches the signals from that equipment.

Press the [Play] button to start playback on

the video equipment.

Press

to switch the image source

to Video.

Change the setting at the DVD to RGB

output.

Zoom adjustment and focus adjustment are performed after the lamp lights.

If you push

once it adjusts one step, and holding it down adjusts

it continuously.

Focus adjustment

If you press

, the adjustment icon will appear on the image.

Press

and

to adjust the focus.

Press

once more to complete the adjustment.

Adjustment can also be carried out while the test pattern is displayed.

Projection image position adjustment (Lens shift)

Use the two lens shift dials to adjust the image position.

When the lens shift dial is turned, a point of resistance will be felt.

This indicates the approximate centre point for the range of adjustment. In

addition, if the lens shift dial becomes hard to turn further and the image

position stops changing, no further adjustment is possible.

Setting up" - Lens shift adjustment

Fine adjustments to image size (Zoom adjustment)

If you press

, the adjustment icon will appear on the image.

Press

and

to adjust the zoom.

Press

once more to complete the adjustment.

Adjustment can also be carried out while the test pattern is displayed.

When

is pressed, a

if adjustment is not possible, it means that "Zoom Lock" or "Focus

Lock" is operating. Turn the lock function off if you would like to make

adjustments.

User's Guide: "Configuration Menu Functions"

Retract

Extend

on the

indicator will flash green.

Example of output selection

After startup, change the Control Panel

adjustment so that mirroring is active.

"When the Indicators Provide No Help" in the User's Guide.

Images appear greenish or purplish

will be displayed on the screen and

Correcting keystone distortion (Keystone)

When you wish to adjust the projection above or below the range of lens

shift adjustment set the projector at an angle.

When the projector is angled, the projected image may distort into a

trapezoid. In such cases, press

(

)

(

control panel to adjust the images.

However, the image quality will decrease compared to if the lens shift

function is used.

When the lens is shifted to the left or right, complete keystone correction is

not possible. When making keystone corrections set the lens at the centre

left to right.

If the message "The projector is overheating. Make sure

nothing is blocking the air vent, and clean or replace the

air filter." is displayed, press

to turn the power

off, and then do as instructed in the message.

indicator

Selecting the image source

If more than one signal source has been connected, or if no images are

projected, use the remote control or the projector's control panel buttons to

select the signal source.

Using the remote control

Press the button that has the name of the port on it that the desired signal

source is connected to.

If the signal source is connected to the [D4] port or to the [InputA] or [InputB] port,

press

to switch the video signals to match the signals from

the video equipment.

Component video :

D4 (Auto)

(Default setting)

Component: Auto

If the colours appear unnatural, set to

Component: YPbPr

RGB Video :

RGB-Video

D4 (Auto)

The setting changes as follows

each time you press

D4 (YPbPr)

The source changes as follows

Component :Auto

each time

RGB RGB-Video

is pressed.

Selecting using the projector's control panel

When you press

displayed.

Use

and

to select the signal source.

Press

to accept.

If "D4", "Input A" or "Input B" is selected, a menu

for selecting the signal format is displayed.

Select the one that matches the image signal of the

connected equipment.

Selection menu

Do the input signal settings

Press

match the projector

the video input source and select the format

settings?

that matches the signals from that equipment.

If connected to the

[InputA] or [InputB] port

Displaying a test pattern

You can project a test pattern at times such as when setting up the projector in order

to correct keystone correction and to make line menu adjustments.

on the remote control is pressed, the pattern selection menu appears.

Selection Menu

Clears the test pattern display

Cross-hatching

This can be used to check whether the projector is

tilted or set up vertically in front of the screen.

Gray Scale

This is used when adjusting brightness or when

adjusting image quality or colour tone. The adjustment

is made using the line menu. Adjustments other than

brightness are not possible when no image signals

are being input.

) on the projector's

15°

Keystone distortion can be corrected within a

maximum vertical angle of approximately 15°.

Attach the lens cover.

Attach the lens cover when not using the projector in order to

keep the lens free from dust and other foreign objects.

When the projector will not be used for long time,

disconnect the power cable from the electrical outlet.

Always make sure that the projector is in the standby condition

before disconnecting the plug. After the power plug is

disconnected, the

indicator will continue to light for a brief

period and then it will turn off.

Disconnect the cables that are connecting other

equipment to the projector.

Setup Guide

(Default setting)

Component: YCbCr

D4 (YCbCr)

Component :YCbCr

Component :YPbPr

, the selection menu is

in accordance with

15°

Printed in Japan

404801400E

03.11-.8A(C05)