- ページ 7

無線アクセスポイント Cisco Linksys WAP610NのPDF ユーザーマニュアルをオンラインで閲覧またはダウンロードできます。Cisco Linksys WAP610N 41 ページ。 Wireless-n access point with dual-band
Cisco Linksys WAP610N にも：クイック・インストール・マニュアル (8 ページ)

ページを印刷する

Chapter 3

If you want to set a permanent static IP address for the

Access Point, then select Static IP.

If you select Static IP, then complete the following fields:

•

Static IP Address

Enter a unique IP address that will

be used to access the browser-based utility.

Subnet Mask

•

Enter the subnet mask of your wired

network.

Default Gateway

Enter the IP address of the default

•

gateway for your network (in most cases, this is your

router).

Click Save Settings to apply your changes, or click Cancel

Changes to cancel your changes.

Wireless > Basic Wireless Settings

Use the Basic Wireless Settings screen to configure the

Access Point's basic wireless and security settings.

There are two ways to configure the Access Point's

settings, manual and Wi-Fi Protected Setup™. Wi-Fi

Protected Setup™ is a feature that makes it easy to set

up your wireless network. If you have client devices, such

as wireless adapters, that support Wi-Fi Protected Setup,

then you can use Wi-Fi Protected Setup to configure

wireless security for your wireless network.

Configuration View

wireless network, select Manual. Then proceed to

"Basic Wireless Settings (Manual)" on page 4. To use Wi-

Fi Protected Setup, select Wi-Fi Protected Setup. Then

proceed to "Wi-Fi Protected Setup™" on page 6.

Basic Wireless Settings (Manual)

Wireless > Basic Wireless Settings (Manual)

Wireless Band

This is used to select the 2.4 GHz or 5.0

GHz band.

Wireless-N Access Point with Dual-Band

manually

configure

your

Advanced Configuration

Network Mode (5 GHz)

From this drop-down menu, you

can select the wireless standards running on your network.

If you have only Wireless-A devices in your network, select

Wireless-A Only. If you have only Wireless-N devices

in your network, select Wireless-N Only. If you have

Wireless-N and Wireless-A devices in your network, keep

the default setting, Mixed.

Network Mode (2.4 GHz)

you can select the wireless standards running on your

network. If you have Wireless-N, Wireless-G, and Wireless-B

devices in your network, keep the default, Mixed. If you

have only Wireless-N devices, select Wireless-N Only. If

you have only Wireless-G and Wireless-B devices in your

network, select Wireless-B/G Only. If you have only

Wireless-G devices, select Wireless-G Only. If you have

only Wireless-B devices, select Wireless-B Only.

Network Name (SSID)

The SSID is the network name

shared among all points in a wireless network. The SSID

must be identical for all devices in the wireless network. It

is case-sensitive and must not exceed 32 characters (use

any characters on the keyboard). Make sure this setting is

the same for all points in your wireless network. For added

security, you should change the default SSID (linksys) to a

unique name.

Channel Width

For best performance in a Wireless-N

network, select 40MHz only. For Wireless-A, Wireless-G,

and Wireless-B networking only, or if you are not sure

which option to use, keep the default, 20MHz only.

NOTE:

If you select 40MHz only for the Channel

Width setting, then Wireless-N can use two

channels: a primary one (Wide Channel) and

a secondary one (Standard Channel). This will

enhance Wireless-N performance.

Wide Channel

If you selected 40 MHz only for the

Channel Width setting, then select the appropriate

channel for your wireless network. If you are not sure

which channel to select, then keep the default, Auto.

Standard Channel

If you selected 20 MHz only for

the Channel Width setting, then select the appropriate

channel for your wireless network. If you are not sure

which channel to select, keep the default, Auto. If you

selected 40MHz only for the Channel Width setting,

then the Standard Channel will be a secondary channel

for Wireless-N. If you selected a specific channel for the

Wide Channel setting, then the Standard Channel options

will be available. Select the appropriate channel for your

wireless network.

SSID Broadcast

When wireless clients survey the local

area for wireless networks to associate with, they will detect

the SSID broadcast by the Access Point. To broadcast the

Access Point's SSID, keep the default setting, Enabled. If

From this drop-down menu,