- ページ 11

ウェザーステーション ACU-RITE 999143のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。ACU-RITE 999143 13 ページ。 Professional weather center

ページを印刷する

INDOOR TEMPERATURE

INDOOR HUMIDITY

BAROMETRIC PRESSURE (must be set to MANUAL mode to calibrate)*

*To change from AUTO to MANUAL pressure mode and vice versa, press

AND HOLD the "

" button for 5-7 seconds. The display indicates the

current pressure mode selected, "AUTO" or "MANUAL". The "

appear next to the barometric pressure to indicate that MANUAL mode has

been activated. Press and HOLD the "

to AUTO mode.

After 5-10 seconds of inactivity, the display will save the adjustments and exit

calibration mode. Note: Calibrations will be erased if the display is reset or if

batteries are removed and the power adapter is unplugged.

Calibrate the Rain Gauge

The rain gauge on the 5-in-1 sensor can be calibrated to improve accuracy.

Items Needed: 5-in-1 sensor, display unit, plastic cup, pin, screw driver

1. First, ensure 5-in-1 sensor is perfectly level using built-in bubble level.

2. Place display unit close so you can monitor it during calibration.

3. Make a pin hole in the bottom of a plastic cup. Hold the cup over the rain gauge and

fill it with exactly 1 cup (8oz) of water, allowing the water to drip into the rain gauge.

You should hear the internal buckets tip and see water drain through the rain gauge.

4. A few seconds after each bucket tip, the display unit displays rainfall in

approximately 0.01" or more increments.

5. The cup of water should take more than 20 minutes to empty; a quicker period will

result in inaccurate calibration. Try to simulate a normal steady rainfall. When cup is

empty of water, display unit should register 1.06"

Tips

• There should be nearly an equal number of water drops (about 25 water drops)

between bucket tips. If not, adjust the calibration screws on the bottom of the 5-in-1

sensor until an equal number of water drops are tipping the buckets. Then, restart the

calibration procedure.

• If you don't hear the buckets tipping and see water dripping alternately out of

each drain, there may be an issue with the rain gauge or it's adjustment. See

Troubleshooting on page 18.

Adjustment

If the rain gauge doesn't register close to 1.06", make an EQUAL adjustment to the two

calibration screws on the bottom of the 5-in-1 sensor. Turning screws clockwise increases

rainfall; counter clockwise decreases rainfall.

• To adjust the rainfall reading by 2% turn both screws 1/8 of a turn.

• To adjust the rainfall reading by 4% turn both screws 1/4 of a turn.

• To adjust the rainfall reading by 8% turn both screws 1/2 of a turn.

Watch the video at www.acurite.com/5in1

" icon will

" button for 5-7 seconds to return

Specifications

TEMPERATURE RANGE

Outdoor: -40ºF to 158ºF; -40ºC to 70ºC

Indoor: 32ºF to 122ºF; 0ºC to 50ºC

HUMIDITY RANGE

Outdoor: 1% to 99%

Indoor: 1% to 99%

WIND SPEED

0 to 99 mph; 0 to 159 kph

WIND DIRECTION

16 points

INDICATORS

0 to 3937 in; 0 to 99999mm

RAINFALL

WIRELESS RANGE

330ft / 100m

OPERATING FREQUENCY

433 MHz

POWER

Display: 4.5V AC, 250mA adapter

3 x AA alkaline batteries (optional)

Sensor: 4 x AA alkaline or lithium batteries

DATA REPORTING

Wind Speed: 18 second updates; Direction: 30 seconds

Outdoor temperature & humidity: 36 second updates

Indoor temperature & humidity: 60 second updates

AcuRite Connect CSV Data Logging: 12 minute intervals

AcuRite Connect to AcuRite Software/App: 18 seconds

DISPLAY UNIT MEMORY

512 kilobytes (not expandable)

ACURITE CONNECT SYSTEM

Windows 8.1 / 8 / 7; 1 GHz or faster processor; 1 GB

REQUIREMENTS

(32-bit) or 2 GB (64-bit) of RAM; available USB port

High speed internet is required for some advanced

features of AcuRite Connect, such as the

AcuRite software and app.

FCC Information

This device complies with part 15 of FCC rules. Operation is subject to the following two conditions:

1- This device may NOT cause harmful interference, and

2- This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed

to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could

void the user authority to operate the equipment.

This device complies with Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions:

(1) This device may not cause interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation of the device.

depending on home construction materials