Cisco TelePresence Video Systems
Contents
Configuring H.323 and SIP
(when not set by a provisioning system)
to get online and ready to place and receive calls, your system
must be set up properly. Your system uses either the H.323
protocol or the SiP protocol for video calls.
NoTe:
Contact your system administrator, or service provider,
for information about the network settings.
for networks administered through Cisco tMS (Cisco
telePresence Management Suite) your Cisco tMS adminis-
trator will help you to get online.
You can find information about admininistering through Cisco
uCM in the
Administering tC endpoints on CuCM
Always save the new value when you change a setting
• drop down list selection: Navigate to the correct value
and press the
OK
( )
key to save, or press the left arrow
key
to leave without saving.
• text entry in an input field: enter the text, navigate to
Ok/Save
to save the change, or navigate to
leave without saving; then press
theOK
Back to task overview
D14639.09 Video Systems Getting Started Guide TC6.1, April 2013.
Introduction
User interfaces
H.323
if in doubt for any of the parameters below, contact your
system administrator or your service provider.
1. Go to
Home > Settings > Administrator settings > Advanced
configuration > H323 > Profile
2. Go to
H323Alias
corresponding input fields.
3. if you want the system to obtain the H.323 gatekeeper
address automatically, go to
in the
Discovery
address manually, select
if set to
guide.
Address
4. if the H.323 gatekeeper requires authentication and you
want your system to authenticate itself to the gatekeeper,
go to
Authentication
list; otherwise select
if set to
On
corresponding input fields.
5. Go to
Home > Settings > System information
the H323 settings.
if you successfully registered to the Gatekeeper the
is shown as
6. Press
Home
Please check the administrator guide for your product if you
want to change the other H.323 settings.
Cancel
to
( ) key
to confirm.
Confirguration
Configuration
1.
and enter the
E164
number and
ID
Gatekeeper
and select
drop down list; if you want to enter the
Manual.
Manual
enter the gatekeeper address in the
input field.
and select
On
in the
Mode
drop down
Off.
enter the
LoginName
and
Password
and verify
Registered
in the H323 section.
(
)
to exit.
20
Appendices
SIP
if in doubt for any of the parameters below, contact your
system administrator or your service provider.
1. Go to
Home > Settings > Administrator settings > Advanced
configuration > SIP > Profile
in the
2. Go to
URI
and enter the SiP uri in the corresponding
input field.
3. Select your preferred
Auto
drop down list. if you select
connect using tls, then tCP, and finally udP.
4. Select your preferred proxy
default type is Standard.
5. Go to
Proxy 1.
if you want the system to obtain the SiP
proxy address automatically, select
drop down list; if you want to enter the address manually,
select Manual.
if set to
Manual
enter the proxy address in the
input field.
in the
6. if the SiP proxy requires authentication you must enter a
login name and password to authenticate your system. Go
to
Authentication 1
and enter the
in the corresponding input fields.
Status
7. Go to
Home > Settings > System information
the SiP settings.
if you successfully registered to a SiP server the
shown as
Registered
8. Press
Home
(
)
to exit.
Please check the administrator guide for your product if you
want to change the other SiP settings.
Copyright © 2010–2013 Cisco Systems, Inc. All rights reserved.
Getting Started Guide
Contacts
1.
DefaultTransport
protocol in the
Auto
the system first tries to
Type
in the drop down list. the
Auto
in the
Discovery
Address
LoginName
and
Password
and verify
Status
is
in the SiP section.
ページを印刷する