会議システム Cisco TelePresence MX300のPDF マニュアルをオンラインで閲覧またはダウンロードできます。Cisco TelePresence MX300 2 ページ。 Telepresence c series
telepresence mx series
telepresence sx series
telepresence ex series
Cisco TelePresence MX300 にも： スタートマニュアル (42 ページ), クイック・リファレンス・マニュアル (2 ページ), クイック・スタート・マニュアル (12 ページ), クイック・リファレンス・マニュアル (2 ページ), トラブルシューティングマニュアル (37 ページ), スタートマニュアル (46 ページ)
ページを印刷する
Installing Cisco TelePresence MX300 - Floor Stand
The MX300 delivery
The MX300 with a floor stand is delivered in three boxes
with the following parts:
•
Floor stand column, floor stand base and floor stand
covers. Screws and Allen key
•
LCD video unit, touch controller, microphones and
cables. Screws, screwdriver and gloves
•
Back cover
Manpower
Two people working together are required to mount the
LCD video unit to the floor stand column.
Dimensions
Height (without camera): 1420 mm / 56 in.
Width: 1290 mm / 51 in.
Depth: 730 mm / 29 in.
Weight: 42 kg / 93 lb
Documentation
The user documentation for this product, including
compliance and safety information, is available on the Cisco
web site, http://www.cisco.com/go/telepresence/docs.
78-20502-01 MX300 Floor Stand Installation Sheet | 2011 NOVEMBER | © 2011 Cisco Systems, Inc. All rights reserved.
1
Unpacking the floor stand box and mounting the floor stand
i
Unpack the floor stand box with the floor stand
base, floor stand column and floor stand covers,
screws and Allen key.
ii
Place the floor stand base on the floor with the
cable channel facing upward and backward.
iii
Raise the floor stand column with the cable
channel facing backward. Place the column
on the base and make sure the holes for the
screws are aligned.
iv
Fasten the column to the base using the four
Floor stand
screws (tool: Allen key).
column
Floor stand
Front
base
The two floor stand covers
will be mounted in step 6.
2
Unpacking the MX300 box with the LCD video unit, Touch controller and accessories
i
Cut the straps and lift off
the outer covering.
Touch controller
ii
Remove the upper foam
with cable
protection.
Note:
Leave the LCD
video unit in the bottom
Outer
tray for now.
covering
iii
Lift out the rectangular
box behind the LCD video
unit.
This box contains two
smaller boxes: One with
the Touch controller, and
one accessories box with
the microphones, cables,
screws and screwdriver.
LCD video
unit
Bottom tray
3
Mounting the LCD video unit to the floor stand
Note:
Always use the provided gloves when handling
the LCD video unit to avoid stains on the unit's surface.
Accessories box:
i
Lift the LCD video unit from the
•
Two microphones
bottom tray and slide it onto the
•
Power cable
top of the floor stand column.
•
Presentation cable
Two people working together are
(VGA to DVI-I; stereo audio)
required for this operation.
31 kg / 68 lb
•
Ethernet cable
•
Four screws for fastening
ii
Remove the cable channel lid (see illustration) to
the LCD video unit to the
get access to the holes for the screws.
floor stand
iii
Fasten the LCD video unit to the column using the
•
Hexagonal screwdriver
four screws (tool: hexagonal screwdriver).
•
Two pairs of gloves
LCD video
unit
Cable channel lid
(for strain relief)
Floor stand