- ページ 3

ネットワーク・ハードウェア Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module ExpansionのPDF 設定マニュアルをオンラインで閲覧またはダウンロードできます。Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion 8 ページ。 Distributed forwarding card 4 for ws-x68xx, ws-x69xx, and select ws-x67xx modules
Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion にも： インストレーション・ノート (14 ページ), 解決マニュアル (17 ページ), インストレーション・ノート (46 ページ), ホワイトペーパー (19 ページ), 説明 (1 ページ), 製品情報 (6 ページ), お知らせ (4 ページ), データシート (9 ページ), データシート (18 ページ), ホワイトペーパー (18 ページ), インストレーション・ノート (28 ページ), トラブルシューティングマニュアル (11 ページ), インストレーション・ノート (18 ページ), ユーザーマニュアル (17 ページ), インストレーション・ノート (24 ページ), マニュアル (19 ページ), インストレーション・ノート (36 ページ)

ページを印刷する
Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion 設定マニュアル
Chapter 4
Configuring a Supervisor Engine 720
Understanding How the Switch Fabric Functionality Works
These sections describe how the switch fabric functionality works:
•
•
•
Switch Fabric Functionality Overview
The switch fabric functionality is built into the Supervisor Engine 720 and creates a dedicated
connection between fabric-enabled modules and provides uninterrupted transmission of frames between
these modules. In addition to the direct connection between fabric-enabled modules provided by the
switch fabric funtionality, fabric-enabled modules also have a direct connection to the 32-Gbps
forwarding bus.
Forwarding Decisions for Layer 3-Switched Traffic
Either a PFC3 or a Distributed Feature Card 3 (DFC3) makes the forwarding decision for Layer
3-switched traffic as follows:
•
•

Switching Modes

With a Supervisor Engine 720, traffic is forwarded to and from modules in one of the following modes:
•
•
•
Table 4-1
OL-3999-08
Switch Fabric Functionality Overview, page 4-3
Forwarding Decisions for Layer 3-Switched Traffic, page 4-3
Switching Modes, page 4-3
A PFC3 makes all forwarding decisions for each packet that enters the switch through a module
without a DFC3.
A DFC3 makes all forwarding decisions for each packet that enters the switch on a DFC3-enabled
module in these situations:
If the egress port is on the same module as the ingress port, the DFC3 forwards the packet
–
locally (the packet never leaves the module).
–
If the egress port is on a different fabric-enabled module, the DFC3 sends the packet to the
egress module, which sends it out the egress port.
–
If the egress port is on a different nonfabric-enabled module, the DFC3 sends the packet to the
Supervisor Engine 720. The Supervisor Engine 720 fabric interface transfers the packet to the
32-Gbps switching bus where it is received by the egress module and is sent out the egress port.
Compact mode—The switch uses this mode for all traffic when only fabric-enabled modules are
installed. In this mode, a compact version of the DBus header is forwarded over the switch fabric
channel, which provides the best possible performance.
Truncated mode—The switch uses this mode for traffic between fabric-enabled modules when there
are both fabric-enabled and nonfabric-enabled modules installed. In this mode, the switch sends a
truncated version of the traffic (the first 64 bytes of the frame) over the switch fabric channel.
Bus mode (also called flow-through mode)—The switch uses this mode for traffic between
nonfabric-enabled modules and for traffic between a nonfabric-enabled module and a fabric-enabled
module. In this mode, all traffic passes between the local bus and the supervisor engine bus.
shows the switching modes used with fabric-enabled and nonfabric-enabled modules installed.
Catalyst 6500 Series Switch Cisco IOS Software Configuration Guide, Release 12.2SXF
Configuring and Monitoring the Switch Fabric Functionality
4-3