- ページ 31
ネットワーク・ハードウェア Cisco CSC-C2FCITのPDF インストールとアップグレードをオンラインで閲覧またはダウンロードできます。Cisco CSC-C2FCIT 32 ページ。 Fddi card and appliques
To prevent damaging the new EPROM and PROM components, ensure that you replace
Caution
each component with the notched end in the correct orientation. Align the notch on the new
component with the notch on the socket. Do not use the label on the component as an indicator for
correct orientation.
Step 7
Replace the card in the card cage. Place your thumbs on the ejector levers, and push the
card in firmly until it snaps into place and is firmly seated in the slot.
Looking at the four connectors on the front edge of the C2FCIT card, attach the ribbon
Step 8
cables from left to right. Refer to the section "Connecting Internal and External Cables" on
page 20.
Step 9
Attach any cables that you removed from other cards.
Step 10
Turn ON power to the system for an installation check, which is described in the section
"Testing the Installation" on page 23.
Note
If the microcode component is not installed correctly, or if any of the pins are bent during
installation, the ciscoBus card will not recognize that a card exists in that ciscoBus slot. The
corresponding LED on the ciscoBus card will not light. If this happens, remove the component,
straighten any bent pins, then reinsert it and try again.
To verify the microcode version for the C2FCIT card after the system boots successfully, use the
show controller fddi command as follows:
router# show controller fddi
Fddi0 - hardware version 7.3, microcode version 10.3
Phy-A registers:
cr0 4, cr1 0, cr2 0, status 6, cr3 0
Phy-B registers:
cr0 4, cr1 4, cr2 0, status 6, cr3 0
FORMAC registers:
irdtlb
73A4, irdtneg F85E, irdthtt 5D49, irdmir
irdtrth F85F, irdtmax FBC5, irdtvxt 8585, irdstmc 0810
irdmode 6A20, irdimsk 0000, irdstat 8060, irdtpri 0000
FDDI-T registers
ccb:
0026
cmd:
icb:
0090
arg:
clm:
E002
bcn:
clmbc: 8011
bcnbc: 8011
txchn: 0000
pend:
state: 0003
check: 0000
rxchn: 0000
buf0:
eofch: 0000
buf1:
head:
0A44
cur:
tail:
0A44
cnt:
txq_s: 001C
txq_f: 001C
For descriptions of additional commands and examples, refer to the Router Products Configuration
Guide publication. If you have any problems, contact a customer service representative.
0006
fr:
000F
mdptr: 0000
0003
app:
0004
mdpg:
E016
clbn: 0150
rxoff: 002A
robn: 0000
park:
0000
act:
0000
tail:
eof:
0000
tail:
048C
nxt0: 0468
eof:
0450
nxt1: 0498
pool:
0498
t0:
0030
t1:
0001
t3:
0000
rxlft: 0041
Aarm: 0000
Barm:
Installing and Upgrading the CSC-C2FCIT FDDI Card and Appliques
Upgrading Microcode
FFFF0BDC
mema: 0000
0000
af:
0700
en:
0001
0000
fop:
9078
0000
cnt:
0000
0000
cnt:
0000
0000
tail: 0000
0050
err:
005C
0025
t2:
0028
used: 0000
1388
fint: 9078
31