- ページ 10

ネットワーク・ハードウェア Cisco TelePresence Server 7010のPDF 交換取扱説明書をオンラインで閲覧またはダウンロードできます。Cisco TelePresence Server 7010 23 ページ。 600w ac-input power supply and fan tray replacement
Cisco TelePresence Server 7010 にも：取付説明書 (15 ページ), インストレーション・マニュアル (14 ページ), はじめに (16 ページ), 交換取扱説明書 (18 ページ)

ページを印刷する

Replacing the Chassis

Removing the Existing Chassis from the Rack

Before removing the existing chassis from the rack, you must shut down the system power and

disconnect the power cord and all interface cables. To help avoid problems when you install the new

chassis, label all interface cables with their slot/port address and mark the positions of the chassis

ears (with tape, chalk, or a marker) so that you can install the new chassis in the same position.

Two chassis ears support the chassis in the rack. The ears are secured to the chassis sides and to the

rack posts, so that the chassis is cantilevered off the ears. We recommend that two people perform

this procedure: one person to support the chassis while the other person removes the screws that

secure the ears to the rack.

Follow these steps to remove the existing chassis from the rack:

Step 1

Step 2

Step 3

Step 4

Step 5

This completes the chassis removal procedure. If you have not yet installed the new chassis in the

rack, proceed to the next section.

Installing the New Chassis in the Rack

Mount the chassis in the rack before connecting any interface or power cables. If possible, install the

new, empty chassis in the rack ﬁrst, then install the system components from the old chassis. The

chassis is supported in the rack by two chassis ears, which attach to the sides of the chassis and to

the mounting strips on the rack. Each chassis ear has two studs that ﬁt into holes in either the

interface processor end or the noninterface processor end of the chassis, whichever will be in the

front of the rack. To mount the chassis, install the ears on the chassis ﬁrst, then secure the ears to the

rack mounting posts or strips. We recommend that two people perform this procedure: one person

to support the chassis in the rack while the other person secures the ears to the rack. Before lifting

the chassis, ensure that your path to the rack is unobstructed.

Follow these steps to install the new chassis in the rack:

Step 1

Step 2

Step 3

Step 4

10 Cisco 7010 and Cisco 7505 Chassis Replacement Instructions

Turn off the system power and disconnect the power cord and all interface cables from the

chassis.

Have a second person support the chassis while you perform this step. From the front of

the rack, use a 1/4-inch ﬂat-blade screwdriver to loosen and remove each of the eight

10-32 x 3/8-inch, slotted screws (four on each side) that secure the chassis ears to the rack.

Pull the chassis out of the rack and place it on the ﬂoor or a table.

Use a number 2 Phillips screwdriver to loosen and remove the two M4 x 10-mm, Phillips

ﬂathead screws that secure the ears to the chassis sides.

Pull the ears off the chassis, and place the ears and all fasteners aside.

Position the chassis so that the end that will be in the front of the rack is closest to you.

Figure 5 shows the correct orientation if the noninterface processor end of the chassis will

be installed at the front of the rack.

Attach the right chassis ear to the chassis ﬁrst. Hold the ear in the orientation shown in

Figure 5, with the studs pointing toward the chassis and the mounting strip facing you.

Insert the two studs through the holes on the side of the chassis. The ear should be ﬂush

against the chassis side.

Insert two M4 x 10-mm, Phillips ﬂathead screws through the ears and into the chassis sides.

Use a number 2 Phillips screwdriver to tighten the screws.