Start Here
EPSON Expression
1680
®
1
Unpack Your Scanner
1
Make sure you have everything:
CD-ROM with
EPSON
®
Scan driver
Scanner
and electronic manual
Power cord
USB cable
2
Remove all the packing tape, but leave the two yellow stickers in place
until instructed to remove them.
IMPORTANT!
Leave the stickers in place until
you are instructed to remove them.
STOP: Be sure to install your scanner software first
BEFORE you connect the scanner!
See your Start Here sheet for details.
2
Install the Software
Wait! You must install your software before connecting the scanner
to your computer.
Be sure to close all open programs and turn off any virus
protection programs.
Windows
®
1
Insert the scanner software CD-ROM in the CD-ROM or DVD drive.
The installer starts automatically.
If it doesn't start, double-click
My Computer (in Windows XP,
click Start > My Computer), double-click
EPSON, then double-click
EPSON.
2
You see a message to close all running applications. Click OK.
3
Read the license agreement, then click Agree.
4
At the Software Installation screen, click Install.
Click
5
Wait for Epson Scan and the User's Guide to be installed.
6
At the last screen, click Exit. The EPSON Product Registration
screen appears.
7
Register your scanner as instructed. When finished, click Done
or close your browser. Remove your CD-ROM.
Macintosh
®
1
Insert the scanner software CD-ROM in the CD-ROM or DVD drive.
(If necessary, double-click the
EPSON CD-ROM icon to open it.)
2
Double-click
.
3
You see a message to close all running applications. Click OK.
4
Read the license agreement, then click Agree.
Click
Agree
5
When the Software Installation screen appears, click Install.
6
Follow the on-screen instructions to install your User's Guide.
When you're done installing the User's Guide, click Quit.
7
In Mac
®
OS X, enter your Administrator name and password when
prompted and click OK.
8
Read the license agreement, then click Accept.
9
When you see the EPSON Scan Installer screen, select EPSON
Expression 1680 in the Easy Install menu and click Install.
10
Mac OS X: At the last screen, click Exit. The EPSON Product
Registration screen appears.
Mac OS 8.6-9.x: When you're done installing, restart your Macintosh.
The EPSON Product Registration screen appears when your
system restarts.
Install
11
Register your scanner as instructed. When finished, click Done
or close your browser. Remove the CD-ROM.
3
Connect the Scanner
After your software is installed, it's time to get connected.
1
Remove the yellow tape from the back of the scanner.
STOP: Be sure to install your scanner software first
BEFORE you connect the scanner!
See your Start Here sheet for details.
2
Slide the transportation lock to the UNLOCK position.
Click
Install
Caution: Your scanner won't work unless the transportation lock is in
the UNLOCK position. Also, you may damage the scanner if you leave
it on while it's locked.
3
Connect the scanner to your computer. Use either the USB cable that
came with your scanner or a SCSI cable, if your computer has SCSI
support. Don't connect both cables.
If you're using USB...
Plug the
square end of the USB cable into the scanner's
USB port. Plug the
flat end into any available USB port
on your computer or USB hub. Then go to step 4.
Click
Install
Note: Your scanner may not work correctly if you use a USB cable
other than the one supplied by EPSON, of if you connect your scanner
to a multi-level USB hub system.
If you're using SCSI...
If you have another SCSI device that uses SCSI ID 2, turn the SCSI ID
switch on the back of the scanner to a new number. Do not use 0 or 7.
Unless your scanner is connected in the middle of a SCSI chain,
leave the terminator switch on the back of the scanner turned ON.
Squeeze the lock releases on your SCSI cable, and plug the cable into
either SCSI connector on the back of the scanner. Connect the pin end
of the cable to the SCSI port on your computer.
4
Plug one end of the scanner's power cord into the AC inlet at the back
of the scanner, and the other end into a grounded electrical outlet.
5
Press the
power button on the front of the scanner to turn it on.
The green READY light begins to flash. Wait for the flashing to stop.
6
If you have a USB connection, go to "Your First Scan" on the back of
this sheet.
If you have a SCSI connection, start the Add Hardware Wizard in the
Windows Control Panel and follow the on-screen instructions to let
Windows detect your scanner. Then continue with the instructions on
the back of this sheet to begin scanning.
continue
Turn over
ページを印刷する