- ページ 7

スキャナー Epson 2480 - Perfection PhotoのPDF クイック・スタート・マニュアルをオンラインで閲覧またはダウンロードできます。Epson 2480 - Perfection Photo 8 ページ。 Scanning application force quits on mac os 10.4
Epson 2480 - Perfection Photo にも: 製品情報マニュアル (6 ページ), 製品サポート速報 (1 ページ), 更新マニュアル (2 ページ), 重要な安全上のご注意 (4 ページ), セットアップマニュアル (4 ページ), 製品サポート速報 (23 ページ), マニュアル (11 ページ), 更新 (1 ページ), 製品サポート速報 (40 ページ), 製品サポート速報 (24 ページ), 製品サポート速報 (29 ページ), 製品サポート速報 (8 ページ), 製品サポート速報 (3 ページ), 製品サポート速報 (14 ページ), 製品サポート速報 (12 ページ), 製品サポート速報 (40 ページ), 製品サポート速報 (11 ページ), 製品サポート速報 (40 ページ), 製品サポート速報 (22 ページ), 製品サポート速報 (12 ページ), 製品サポート速報 (21 ページ)

Epson 2480 - Perfection Photo クイック・スタート・マニュアル
Scanning a Slide
1
Make sure you removed the reflective document mat, as described in the
previous column.
2
Place the slide holder on the top of the
scanner glass so that the tab labelled "D"
fits into the area labelled "D" on the
document table.
3
Place a 35 mm slide into the holder with its
shiny base side facing down. Your image
should appear backwards on the side that
faces up.
For a landscape-oriented slide, place the
top of the image toward the left. For a
portrait-oriented slide, place the top of the
image toward the top of the scanner.
4
Close the scanner cover.
5
To scan your slide, press the 4 Scan and Save button or open Epson Smart
Panel and select Scan and Save. This scans your slide using ideal settings
in Full Auto Mode and opens it in ArcSoft PhotoImpression for viewing,
editing, and printing. See your on-screen Reference Guide and Smart Panel
help for instructions on selecting scan modes and complete scanning
details.
6
When you're finished scanning, you can store the slide holder in the scanner
cover. Slide the slide holder into the cover, then replace the document mat.
Problems?
First check the ] Start light on the scanner.
Flashing green
Green
Flashing red
Off
If your problem is listed here, try these suggestions.
The New Hardware
Wizard appears on
your screen.
You see an error
message when you
try to scan or the
scanner doesn't
scan.
You can't scan
negatives or slides.
Warming up or scanning.
Ready to scan.
Make sure the transportation lock is unlocked
(see section 3).
Try restarting your computer and unplugging the scanner.
Wait 10 seconds, then plug the scanner back in.
Film may be jammed in the auto film loader on the
Perfection 2580 Photo. Disconnect the scanner from the
computer, wait 10 seconds, and connect it to the computer
again to see if the film ejects on its own. If film is still
jammed, see your on-screen Reference Guide.
If the red light is still flashing, contact your dealer or Epson.
Make sure your scanner is connected to your computer
and plugged into a power source, and the scanner
software is installed.
Click Cancel and follow the steps in section 2 to install
your software. Disconnect the scanner before you install.
Make sure your scanner is connected to your computer
and plugged into a power source.
Make sure the transportation lock is unlocked
(see section 3).
Uninstall and reinstall Epson Scan. See your on-screen
Reference Guide for instructions.
Make sure the transparency unit cable is connected to
the scanner (see section 3) and the reflective document
mat is removed. Make sure the Document Type setting
and the film holder position are correct for the type of film
you're scanning.