- ページ 2

照明器具 Acuity Brands Aculux AX3 A WDTWのPDF インストレーション・インストラクションをオンラインで閲覧またはダウンロードできます。Acuity Brands Aculux AX3 A WDTW 5 ページ。 Dmx512 / rdm field

ページを印刷する

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL SAFETY INSTRUCTIONS!

SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION

• To reduce the risk of death, personal injury or property damage from fire, electric shock,

falling parts, cuts/abrasions, and other hazards please read all warnings and instructions

included with and on the fixture box and all fixture labels.

• Before installing, servicing, or performing routine maintenance upon this equipment,

follow these general precautions.

• Installation and service of luminaires should be performed by a qualified licensed electrician.

• Maintenance of the luminaires should be performed by person(s) familiar with the

luminaires' construction and operation and any hazards involved. Regular fixture

maintenance programs are recommended.

• It will occasionally be necessary to clean the outside of the refractor/lens. Frequency of

cleaning will depend on ambient dirt level and minimum light output which is acceptable

to user. Refractor/lens should be washed in a solution of warm water and any mild, non-

abrasive household detergent, rinsed with clean water and wiped dry. Should optical

assembly become dirty on the inside, wipe refractor/lens and clean in above

manner, replacing damaged gaskets as necessary.

• DO NOT INSTALL DAMAGED PRODUCT! This luminaire has been properly packed so

that no parts should have been damaged during transit. Inspect to confirm. Any part

damaged or broken during or after assembly should be replaced.

• Recycle: For information on how to recycle LED electronic products, please visit

www.EPA.gov

• These instructions do not purport to cover all details or variations in equipment nor to

provide every possible contingency to meet in connection with installation, operation, or

maintenance. Should further information be desired or should particular problems arise

which are not covered sufficiently for the purchaser's or owner's purposes, this matter

should be referred to Acuity Brands Lighting, Inc.

WARNING RISK OF ELECTRIC SHOCK

• Disconnect or turn off power before installation or servicing.

• Verify that supply voltage is correct by comparing it with the luminaire

label information.

• Make all electrical and grounded connections in accordance with the National

Electrical Code (NEC) and any applicable local code requirements.

• All wiring connections should be capped with UL approved recognized

wire connectors.

CAUTION RISK OF INJURY

• Wear gloves and safety glasses at all times when removing luminaire from carton,

installing, servicing or performing maintenance.

• Avoid direct eye exposure to the light source while it is on.

All luminaires that contain electronic devices that generate frequencies above 9kHz

from any component within the luminaire comply with one of the following Part 15 of

the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference

(2) This device must accept any interference recieved, including

interference that may cause undesired operation.

This device complies with Part 18 of the FCC Rules, but may cause interference with

cordless and cell phones, radios, televisions, and other electronic devices. To correct

the problem move the device away from the luminaire or plug into a different outlet.

This product may cause interference to radio equipment and should not be installed

near maritime safety communications equipment or other critical navigation or

communications equipment operating between 0.45-30MHz.

Product Services Phone (888) 387-2212

1300 S. Wolf Road • Des Plaines, IL 60018 • Phone 800-323-5068 • Visit us at www.acuitybrands.com/aculux

INSTALLATION INSTRUCTIONS

CAUTION: RISK OF PRODUCT DAMAGE

• Never connect components under load.

• Do not mount or support these fixtures in a manner that can cut the outer jacket or

damage wire insulations.

• Never connect an LED product to an unapproved dimmer pack. Contact ABL directly for any

dimmers not specifically recommended for the product.

• LEDs are polarity Sensitive. Ensure proper Polarity before installation.

• Electrostatic Discharge (ESD): ESD can damage LED fixtures. Personal grounding

equipment must be worn during all installation or servicing of the unit.

• Do not touch individual electrical components as this can cause ESD, shorten lamp life,

or alter performance.

WARNING RISK OF BURN

• Allow lamp/fixture to cool before handling. Do not touch enclosure or light source.

• Follow all manufacturer's warnings, recommendations and restrictions for: driver

type, burning position, mounting locations/methods, replacement and recycling.

CAUTION RISK OF FIRE

• Keep combustible and other materials that can burn, away from lamp/lens.

• Do not operate in close proximity to persons, combustible materials or substances

affected by heat or drying.

Failure to follow any of these instructions could void product warranties. For a

complete listing of product Terms and Conditions, please visit

www.acuitybrands.com

OUR BRANDS

Indoor/Outdoor: Lithonia Lighting, Carandinim Holophane, RELOC

Indoor Lighting: Gotham, Mark Architectural Lighting, Peerless, Renaissance

Lighting, Winona Lighting, Juno, Aculux, Indy

Outdoor Lighting: American Electric Lighting, Antique Street Lamps, Hydrel, Tersen

Controls: DARK TO LIGHT, Lighting Control & Design, ROAM, Sensor Switch,

Synergy

Acuity Brands Lighting, Inc. assumes no responsibility for claims arising out

of improper or careless installation or handling of its products.

Rev 3/17

P6160

2 of 5