- ページ 4

プリンターアクセサリー Epson FX-1180 - Impact PrinterのPDF マニュアルをオンラインで閲覧またはダウンロードできます。Epson FX-1180 - Impact Printer 18 ページ。 Epson serial impact dot matrix printers
Epson FX-1180 - Impact Printer にも: セットアップマニュアル (33 ページ), パンフレット&スペック (24 ページ), 製品情報 (17 ページ), クイック・リファレンス・マニュアル (16 ページ), マニュアル (11 ページ), 仕様 (2 ページ), 仕様 (2 ページ), 限定保証 (1 ページ), リファレンス・マニュアル (34 ページ), クイックマニュアル (33 ページ)

Epson FX-1180 - Impact Printer マニュアル
EPSON FX-880+/FX-1180+
Environmental
Temperature
Operation (plain
41 to 95 °F (5 to 35 °C)
paper)
Operation
59 to 77 °F (15 to 25 °C)
(recycled paper,
envelopes, labels
or roll paper)
Storage
–22 to 140 °F (–30 to 60 °C)
Paper
Use recycled paper, multipart paper, labels, envelopes,
and roll paper only under normal temperature and
humidity conditions, as follows:
Temperature
Humidity
Do not load paper that has been folded or is damaged,
wrinkled, or curled.
Single sheets, front or rear entry
Minimum
*
Width
(inch)
3.9
(mm)
100
**
Length
(inch)
3.9
(mm)
100
***
Thickness
(inch)
0.0025
(mm)
0.065
Weight
(lb)
14
(g/m²)
52
Quality
Plain paper and recycled paper
* 7.2 to 8.5 inches (182 to 216 mm) for the optional cut-sheet
feeder for FX-880+.
7.2 to 16.5 inches (182 to 420 mm) for the optional cut-sheet
feeder for FX-1180+.
** 8.3 to 14.3 inches (210 to 364 mm) for the optional cut-sheet
feeder.
***0.0028 to 0.0055 inch (0.07 to 0.14 mm) for the optional
cut-sheet feeder.
4 - EPSON FX-880+/FX-1180+
Humidity (without
condensation)
10 to 80% RH
30 to 60% RH
0 to 85% RH
59 to 77 °F (15 to 25 °C)
30 to 60% RH
Maximum
FX-880+:
FX-1180+:
10.1
16.5
257
420
14.3
364
0.0055
0.14
24
90
Single-sheet multipart forms (for the optional front
sheet or front paper guide only):
Width
(inch)
(mm)
Length
((inch)
(mm)
Copies
Total thickness
(inch)
(mm)
Weight per sheet of
multipart
(lb)
(g/m²)
Quality
Continuous paper (ordinary and multipart):
Width
(inch)
(mm)
Length, one page
(inch)
(mm)
Copies
Total thickness
(inch)
(mm)
Weight, ordinary
paper
(lb)
(g/m²)
Weight per sheet of
multipart
(lb)
(g/m²)
Quality
Do not load thick paper, such as multipart forms with
five or six parts, in the rear slot.
The ratio of the cut/uncut length at the perforation
should be between 3:1 and 5:1.
The thickness of the perforation part when extended
should be 1 mm or less.
The perforation between pages should not extend all
the way to the edges of the paper. Uncut length on the
edges should be 1 mm or more.
The horizontal and vertical perforation cuts should not
cross.
10/01
Minimum
Maximum
FX-880+:
3.9
10.1
100
257
3.9
14.3
100
364
1 original + 5 copies
0.0047
0.018
0.12
0.46
12
15
40
58
Carbonless multipart forms with a line of glue at
the top or one side of the form
Minimum
Maximum
FX-880+:
4.0
10.0
101.6
254.0
4.0
22.0
101.6
558.8
1 original + 5 copies
0.0025
0.018
0.065
0.46
14
22
52
82
12
15
40
58
Plain paper, recycled paper, and carbonless
multipart forms with point gluing or paper
stapling on both sides
FX-1180+:
16.5
420
FX-1180+:
16.0
406.4