- ページ 2

扇風機 Argos Manhattaan 432/5114のPDF 組立・取付説明書をオンラインで閲覧またはダウンロードできます。Argos Manhattaan 432/5114 4 ページ。 Clear sat nickel rc ceiling fan

ページを印刷する

FIGURE 2

CANOPY

SCREW

BAYONET

SLOT

ROUND HOLE

FIGURE 3

DOWNROD

EARTH TERMINAL

LIGHT SUPPLY

(RED)

WIRES TO FAN

RECEIVER

PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor

Please read these instructions carefully before attempting to install this ceiling fan. It is also advis-

able to keep these instructions in a safe place for future reference.

Before installing and using this ceiling fan, read the list of Do and Don'ts below.

Do not use the ceiling fan and open gas heating appliances in the same room at the same time.

It is important that the correct electrical connections are made and that the mountingplate is fitted

to an adequate ceiling support. Ceiling fans are heavy, so it is important that they should be

suspended securely. If in any doubt about the installation of this product consult a qualified

electrician.

This product must be installed in accordance with national building regulations.

When deciding on the location for your ceiling fan make sure that there will be plenty of room for

the rotation of the fan blades and that no obstacles are likely to get in their way. The distance

betweenthe fan blades and the floor should be at least 2.3m (7½ft).

Crosshead and slotted screw drivers

1xMax.40w E14 buld(NOT INCLUDED)

Step ladder

Insulating tape

MOUNTING PLATE

Remove the upper polystyrene cover from the box .Take the motor out of the box and place it on

the polystyrene cover ,or on a soft padded surface to protect it during the installation procedure.

Keep all packing material for future protection in transit.

BALL JOINT

CANOPY

1.Unscrew the four screws on the ceiling canopy to release the mounting plate(Figure 1). Secure

the mounting plate to a ceiling joist ,or an equally secure ceiling structure using the two wood fix-

ing screws and washers supplied. The support for the mounting plate must be capable of safety

and securely holding the moving weight of the fan. Note that additional strengthening of the joist

might be necessary.

2.For best fan performance and safety,make sure the mounting plate is fitted to a level ceiling

joist or ceiling support. If the mounting position is not level, hard packing material should be used

to make the plate level.

RECEIVER

1.Hang the ball joint and the fan onto the bracket. Make sure the guled pon of bracket is fitted

into slot of ball joint.(Figute 2) With the fan suspended in this manner, you can now make the

appropriate electrical connections. See the CONNECTION TO THE LIGHT CIRCUIT section.

2.insert the remote control receiver betwwen the bracket and the downrod. And the sensor as

shown.(Figure 2)

3.Fix conopy onto the bracket by tightening the screws.(Figure 4)

MATE

Ensure electricity is switched off at the mains before installing or maintaining this fitting.

CONNECTOR

Any switches connected to the ceiling fan must conform to the necessary British Standards. If you

are not sure how to wire the ceiling fan consult a qualified electrician. For the basic means of

wiring the ceiling fan (model 1 above) use the following procedure(Figure 3)

Blue or black (Neutral)to the terminal marked N

Brown or Red (Live)to the terminal marked L

Green/Yellow or Green (Earth)to the terminal marked

Ensure that earth terminal of the canopy is securely connected to the earth pole of the terminal

block.

Ensure that all electrical connections are tight and that no loose strands are left out of the terminal

block. Cover the terminal block with insulation tape.

FAMATE

CONNECTOR

Warning : If there are only two wires in your existing mains wiring,this means that there is no

Ask a qualified electrician to provide an Earth facility.

The installation must be provided with a double pole switch.

INCOMING MAINS SUPPLY

(GREEN /YELLOW)

BLUE

BROWN

ASSEMBLY & FITTING INSTRUCTIONS

IMPORTANT

CAUTION

LOCATION

TOOLS AND MATERIALS REQUIRED

UNPACKING

UNSTALLING THE MOUNTING PLATE

INSTALLING THE FAN

CONNECTION TO THE LIGHT CIRCUIT

Earth. Under no circumstance should you wire up this fitting without using an Earth connection.