Installation Instructions - rPODBA Wireless Switch

SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION

!

WARNING! RISK OF SEVERE INJURY OR DEATH

To reduce the risk of death, injury or property damage from fire, electric shock, cuts, abrasions, falling parts, and other hazards:

•

Read all warnings and instructions included with and on the fixture box and all fixture labels.

•

Installation and service should be performed by a qualified licensed electrician.

•

Maintenance must be performed by a person familiar with the construction and operation of this product and any hazards involved.

All applicable codes and ordinances must be followed.

•

Read this document before installing, servicing, or maintaining this equipment. These instructions do not cover all installation,

service, and maintenance situations. If your situation is not covered, or if you do not understand these instructions or additional

information is required, contact

!

WARNING! RISK OF ELECTRIC SHOCK

Before installing, servicing, or maintaining this equipment, follow these general precautions.

To reduce the risk of electrocution:

!

WARNING! RISK OF FIRE

To reduce the risk of fire:

!

WARNING! RISK OF PERSONAL INJURY

To reduce the risk of personal injury from cuts, abrasions:

!

WARNING! RISK OF PRODUCT DAMAGE

Electrostatic Discharge (ESD) will damage electronic equipment. Do not attempt to open or service electronic equipment without proper ESD

precautions.

Acuity Controls assumes no responsibility for claims arising out of improper or careless installation or handling of this product. Failure to

For a complete listing of product Terms and Conditions, please visit www.AcuityControls.com

Always read complete installation instructions prior to installation!

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier

interferencia, incluyendo la que pueda causar su operación no deseada.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the following measures:

1.

Reorient or relocate the receiving antenna.

2.

Increase the separation between the equipment and receiver.

3.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

4.

Consult the dealer or an experienced radio/TV technician for help.

Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitybrands.com/nLight © 2019-2021 Acuity Brands Lighting, Inc. All rights reserved. 04/29/2021

912-00087-002

READ AND FOLLOW ALL SAFETY INSTRUCTIONS!

IMPORTANT SAFETY INSTRUCTIONS

Acuity Controls.

•

Disconnect or turn off power before installation or servicing.

•

Make sure the equipment is properly grounded.

•

Make all electrical connections in accordance with the National Electrical Code (NEC) and any applicable local code

requirements.

•

Use supply conductors with a minimum operating temperature rating as specified.

•

Do not exceed maximum wattage, ratings, or published operating conditions.

•

Follow all manufacturer's warnings, recommendations and restrictions to ensure proper operation.

•

Wear gloves and safety glasses at all times when installing, servicing or performing maintenance.

•

Do not touch electronic components. ESD damage can occur.

•

Do not change or alter internal wiring or circuitry.

follow any of these instructions could void product warranty.

SAVE THESE INSTRUCTIONS

Contains FCC ID: 2ADCB-RMODIT or 2ADCB-RMODIT3

Contains IC: 6715C-RMODIT or 6715C-RMODIT3

IFT #: RCPACRM18-1879 or RCPNLNL20-2057

Acuity Brands Lighting Inc. RMODIT or RMODIT3

1 of 2