- ページ 10
双方向ラジオ Motorola Commercial SeriesのPDF サービス情報をオンラインで閲覧またはダウンロードできます。Motorola Commercial Series 30 ページ。 Uhf2 (438-470mhz)
Motorola Commercial Series にも: 基本マニュアル (16 ページ), サービス情報 (48 ページ), サービス情報 (46 ページ), ユーザーマニュアル (18 ページ), 基本マニュアル (12 ページ)
1-6
3.2.6
Sensing of Externally-Connected Accessories
Port PJ1 is used to detect the presence of externally connected accessories. Port PJ1 (U401 pin
72) is normally low, unless accessories (lapel speaker microphone, lightweight headset, etc.) are
used with the radio. This port is used to detect an accessory PTT or auto sensing of a VOX
accessory.
If VOX is programmed into the radio channel codeplug information, and PJ1 is high during power-
up, the radio will activate VOX operation. If a low is present at port PJ1 during power-up, the radio
will use this port as an external PTT indicator.
3.2.7
Microprocessor Power-Up, Power-Down and Reset Routine
On power-up, the microprocessor is held in reset until the digital 3.3V regulator (U320 pin 5)
provides a stable supply voltage. Once the digital supply reaches steady state and releases the
reset line (U320 pin 7), the microprocessor begins to start up. The ASFIC_CMP (U451) has already
started running and is providing the startup clock to the microprocessor. After reset release by all
circuits, the software within the microprocessor begins executing port assignments, RAM checking,
and initialization. A fixed delay of 100 ms is added to allow the audio circuitry to settle. Next, an alert
beep is generated and the steady state software begins to execute (buttons are read, radio circuits
are controlled).
When the radio is turned off, SWB+ is removed and port PE0 (U401 pin 67) goes low, initiating a
power-down routine. Port PH3 (pin 44) remains high, keeping the voltage regulators on via Q493
and Q494, until the operating state of the radio has been stored in EEPROM. PH3 then goes low,
and all regulated voltages are removed.
The microprocessor reset line (pin 94) can be controlled directly by the digital 3.3 V regulator (U320
pin 7), the microphone jack (part of accessory connector J471) via Q472 and Q471, and the
microprocessor itself. U320 pulls the reset line low if the digital 3.3 V source loses regulation. This
prevents possible MOS latch-up or overwriting of registers in the microprocessor because the reset
line is higher in voltage than the microprocessor VDD ports (U401 pins 12, 39, 59, 88). The
microprocessor can drive the reset line low if it detects a fault condition such as an expired
watchdog timer, software attempting to execute an infinite loop, unplanned hardware inputs, static
discharge, etc. Finally, the Q471 can pull the reset line low during use of the programming cable and
CPS by the application of a sufficiently negative voltage to the microphone connector tip contact
(J471 pin 4), however this reset method is not utilized.
3.2.8
Boot Mode Control
When power-up reset occurs, the microprocessor will boot into either normal or flash mode
depending on the logic level of ports MODA (U401 pin 58) and MODB (pin 57). The Flash Adapter is
a programming accessory which provides negative 9 volts dc via a 1K resistor to microphone
connector J471 pin 4. This turns on Q471 and Q472 via D471 and VR472, pulling MODA and
MODB low and allowing booting in the flash mode by cycling power to reset the radio. Software
upgrades can then performed by loading the new software code into Flash ROM U404.
THEORY OF OPERATION