- ページ 2

ソフトウェア Epson 3170 - Perfection PhotoのPDF 重要な安全上のご注意をオンラインで閲覧またはダウンロードできます。Epson 3170 - Perfection Photo 4 ページ。 Scanning tips and troubleshooting guide
Epson 3170 - Perfection Photo にも: 製品サポート速報 (34 ページ), ユーザーマニュアル (6 ページ), ここからスタート (4 ページ), 製品サポート速報 (23 ページ), マニュアル (11 ページ), 製品サポート速報 (40 ページ), 製品サポート速報 (17 ページ), 製品サポート速報 (24 ページ), 製品サポート速報 (29 ページ), 製品サポート速報 (8 ページ), 製品サポート速報 (3 ページ), 製品サポート速報 (14 ページ), 製品サポート速報 (18 ページ), 製品サポート速報 (12 ページ), 製品サポート速報 (40 ページ), 製品サポート速報 (40 ページ), 製品サポート速報 (22 ページ), 製品サポート速報 (12 ページ), 製品サポート速報 (21 ページ), トラブルシューティングマニュアル (12 ページ)

Epson 3170 - Perfection Photo 重要な安全上のご注意
Unplug the scanner and refer servicing to qualified service personnel under the following
conditions:
The power cord or plug is damaged; liquid has entered the scanner or the AC adapter; the
scanner or the AC adapter has been dropped or the case damaged; the scanner or AC adapter
does not operate normally or exhibits a distinct change in performance. (Do not adjust controls
that are not covered by the operating instructions.)
Unplug the scanner and AC adapter before cleaning. Clean with a damp cloth only. Do not use
liquid or aerosol cleaners.
If you are not going to use the scanner for a long period, be sure to unplug the AC adapter from
the electrical outlet.
To reduce the risk of fire, use only the included power cord or a 6 to 10 foot long UL-approved
type SPT-2 or heavier, 2 x 18 AWG cord with a 125 V 10 A plug and 125 V 7 A connector.
The AC adapter is equipped with a polarized alternating-current line plug (a plug having one
blade wider than the other). This plug only fits into a power outlet in one way. This is a safety
feature. If you are unable to insert the plug properly, try reversing the plug. If the plug still fails
to fit, contact an electrician to replace your outlet. Be sure to use only the polarized power cord
that comes with the scanner.
This product includes a lamp component that contains mercury. Please consult your state and
local regulations regarding proper disposal or recycling. Do not put in the trash.

FCC Compliance Statement

For United States Users

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio or television reception. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause interference to
radio and television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
WARNING: The connection of a non-shielded equipment interface cable to this equipment will
invalidate the FCC Certification of this device and may cause interference levels which exceed the
limits established by the FCC for this equipment. It is the responsibility of the user to obtain and
use a shielded equipment interface cable with this device. If this equipment has more than one
interface connector, do not leave cables connected to unused interfaces. Changes or modifications
not expressly approved by the manufacturer could void the user's authority to operate the equipment.