- ページ 11

室内暖炉 Dimplex 6908492100のPDF サービスマニュアルをオンラインで閲覧またはダウンロードできます。Dimplex 6908492100 14 ページ。

ページを印刷する

Figure 8

Media Tray

Retaining Screws

Figure 9

Flicker Motor

Flicker Rod

End Bracket

Flicker Rod

12. At this point the whole assembly with the brackets can

be removed from the unit. The end bracket can be

removed from the end of the Flicker Rod and the screws

holding the center bracket can be removed as well.

13. Replace the old Flicker Rod with the new one and reas-

semble in the reverse order.

! NOTE: Ensure that the flicker rod is not bent and the

bushing in the center of the flicker rod is completely set in

the support bracket. The bushing must be properly aligned

for it to go all the way down into the bracket.

14. Re-assemble the remainder of the fireplace in reverse

order from the instructions above.

NOTE: If any tie wraps were removed, replace and en-

sure that none of the wires are pinched during reassembly.

! NOTE: Be sure that the flanges on the end panel are

positioned on the interior of the outside panel of the fire-

place.

End Panel Screws

LED Light

Strip Bracket

Flicker Rod Middle Bracket

FLICKER MOTOR REPLACEMENT

Tools Required: Phillips head screwdriver

Flat head screwdriver

Needle-nose pliers

WARNING: If the fireplace was operating prior to ser-

vicing, allow at least 10 minutes for light bulbs and heating

elements to cool off to avoid accidental burning of skin.

WARNING: Disconnect power before attempting any

maintenance to reduce the risk of electric shock or damage

to persons.

1. On either side of the firebox, remove the retaining

screws and carefully remove the glass assembly from

the rest of the assembly. (Figure 3)

2. Carefully remove the acrylic media from the front tray.

3. If applicable, remove the fireplace assembly from the

wall by carefully lifting it upward, releasing it from the

flanges of the wall-mounting bracket. (Figure 4).

4. Carefully set the unit upright on a flat working surface.

! NOTE: If necessary, lay a protective barrier between

the unit and your work surface, (i.e. cloth, cardboard, thick

plastic) to avoid scratching your work surface.

5. On the right end, with the switchboard, remove the ten

screws around the outside of the end panel. (Figure 5)

6. Lay unit on its back and remove the remaining 9 screws

from the end panel.

7. Remove the end panel being careful not to add any

strain to the wires connecting to the switchboard.

8. Gently guide the partially reflective glass out the open

side of the firebox.

NOTE: The wires are grouped together with tie wraps,

which may need to cut to easily access the different wires.

9. Remove both sets of the 3 end panel screws and the 5

front screws that hold the Media Tray in place. (Figure

10. Inside the lower cavity, locate the Flicker Motor. Re-

move the 2 screws which secure the flicker motor to

the mounting bracket and remove the motor. (Figure 9)

11. Carefully pull and twist the rubber gasket and reflector

rod off of the motor shaft, taking care not to bend the

rod. If the rod gets bent, it may cause a rubbing noise

once the fireplace is re-assembled.

12. Disconnect the flicker motor wires from the wire con-

nectors.

13. Remove the original flicker motor and remove the

rubber barrier that mounts between the motor and the

bracket.

14. Fit the rubber barrier onto the new flicker motor and

mount the flicker motor onto the mounting bracket. Re-

connect the rubber gasket and flicker rod to the flicker

motor.

! NOTE: Ensure that the flicker rod is not bent and the

bushing in the center of the flicker rod is completely set in

the support bracket. The bushing must be properly aligned