- ページ 10
室内暖炉 Dimplex BF33DXPのPDF インストレーション・マニュアルをオンラインで閲覧またはダウンロードできます。Dimplex BF33DXP 14 ページ。 Fireplace
Dimplex BF33DXP にも： 実用マニュアル (15 ページ), オーナーズマニュアル (14 ページ), サービスマニュアル (20 ページ), ユーザーマニュアル (14 ページ), トラブルシューティングマニュアル (2 ページ), オーナーズマニュアル (14 ページ)
ページを印刷する
120V MAIN POWER WALL SWITCH - NO HEAT
!
NOTE: This option should not be used with the remote control kit.
!
NOTE: Before installing the unit have the following wires installed:
1.
A 2 conductor wire with ground (3 wires total) from the power supply panel to the main switch wall box.
2.
A 2 conductor wire with ground (3 wires total) from the main switch wall box to the junction box on the unit.
!
NOTE: Use a single pole, single throw (On/Off) wall switch that is rated for a minimum of 15 amps.
1.
Locate the voltage selector switch inside the exhaust panel on the top right hand corner of the unit.
switch is in the 120V position . (115 is printed on switch)
2.
Loosen the screw securing the junction box cover and remove the cover.
3.
Remove the knockouts (if necessary) or use the provided cable clamp.
4.
Pull out the four wires marked L1, L2, N, and G (black, red, white and green).
5.
Connect L1 (black) from the unit to the L1 wire (black) from the main power wall switch using a wire connector (not sup-
plied).
6.
Connect the other end of the L1 wire (black) to the L1 terminal of the main power wall switch.
7.
Connect L2 (red) from the unit and the N (white) from the unit to the Neutral wire (white) of the main power wall switch by
using a wire connector (not supplied).
8.
Connect the other end of the Neutral wire (white) to the Neutral wire (white) from the power supply panel by using a wire
connector (not supplied).
9.
Connect the Ground wire (green) from the unit to the Ground wire (green) of the main power wall switch by using a wire
connector (not supplied).
10.
Connect L1 (black) from the power supply to the L1 terminal of the main power wall switch.
11.
Locate and separate by wire nut the 1 (red) and 2 (red).
12.
Secure the 2 remaining Ground wires (green)
with a ground screw in the main switch wall
box.
13.
Ensure that all connections are tight.
14.
Insert all the wiring of the main power wall
switch into the main switch wall box.
15.
Insert all the wiring back into the unit and se-
cure with a cable clamp.
10
WHITE - N
RED – L2
BLACK – L1
WALL
RED – 2
SWITCH
RED – 1
WIRE
NUTS
GROUND - G
WHITE – N
120 V
POWER
SUPPLY
BLACK – L1
(BREAKER
PANEL)
GROUND - G
G FROM
POWER SUPPLY
G FROM UNIT
L1 FROM UNIT
NEUTRAL FROM
UNIT AND SUPPLY
L1 FROM
POWER SUPPLY
N
L2
L1
G
N
L2
L1
G
Ensure that the
G FROM
POWER SUPPLY
G FROM UNIT
L1 FROM UNIT
NEUTRAL FROM
UNIT AND SUPPLY
L1 FROM
POWER SUPPLY
2 CONDUCTOR WIRE
FROM POWER SUPPLY
2 CONDUCTOR WIRE
FROM MAIN SWITCH
www.dimplex.com