- ページ 8

室内暖炉 Dimplex BOF4056のPDF サービスマニュアルをオンラインで閲覧またはダウンロードできます。Dimplex BOF4056 12 ページ。
Dimplex BOF4056 にも：オーナーズマニュアル (19 ページ)

ページを印刷する

to the unit, located under the sump.

3. Remove the 4 screws that secure the front grill to the

cassette housing. (Figure 5)

4. Locate the defective switch and disconnect the wiring

connections noting their original locations.

NOTE: A flat head screwdriver can be used to gently

pry between the end of the connector and the switch to

release the wires.

5. Depress the retainer clips on the rear of the switch and

push the switch out through the opening.

6. Properly orient and insert the new switch and connect

all of the wiring.

7. Re-assemble the remainder of the cassette in reverse

order from the instructions above.

Thermostat Replacement

Tools Required: Philips head screwdriver

Flat Head Screwdriver

WARNING: Disconnect power before attempting any

maintenance to reduce the risk of electric shock or damage

to persons.

NOTE: Ensure that all of the components that

contain water have been emptied before performing any

maintenance.

1. Disconnect and remove the media from the unit and

put them in a safe place.

2. Remove the 2 screws that secure the engine assembly

to the unit, located under the sump.

3. Remove the 4 screws that secure the front grill to the

cassette housing. (Figure 5)

4. Remove the knob off of the thermostat, by gently lifting

the bottom forward and pulling down.

5. Depress the retainer clips on either side of the thermo-

stat to slide it out of the assembly.

6. Disconnect the wiring connections noting their original

locations.

NOTE: A flat head screwdriver can be used to gently

pry between the end of the connector and the switch to

release the wires.

7. Install the knob onto the new thermostat and slide the

thermostat back into the assembly ensuring that it has

"clicked" into place.

8. Re-assemble the remainder of the cassette in reverse

order from the instructions above.

Potentiometer Replacement

Tools Required: Philips head screwdriver

Flat Head Screwdriver

3/8" (10mm) Wrench

WARNING: Disconnect power before attempting any

maintenance to reduce the risk of electric shock or damage

to persons.

NOTE: Ensure that all of the components that

contain water have been emptied before performing any

maintenance.

1. Disconnect and remove the media from the unit and

put them in a safe place.

2. Remove the 2 screws that secure the engine assembly

to the unit, located under the sump.

3. Remove the 4 screws that secure the front grill to the

cassette housing. (Figure 5)

4. Turn the unit so that the underside of the potentiometer

can be seen.

5. Loosen the securing nut, to allow the potentiometers

slide out.

6. Disconnect the wiring connections noting their original

locations.

NOTE: A flat head screwdriver can be used to gently

pry between the end of the connector and the switch to

release the wires.

7. Slide the potentiometer back into the assembly and

tighten the securing nut.

8. Re-assemble the remainder of the cassette in reverse

order from the instructions above.

Power Cord / Receptacle Replacement

Tools Required: Philips head screwdriver

Flat head screwdriver

WARNING: Disconnect power before attempting any

maintenance to reduce the risk of electric shock or damage

to persons.

NOTE: Ensure that all of the components that

contain water have been emptied before performing any

maintenance.

1. Disconnect and remove the media from the unit and

put them in a safe place.

2. Remove the 2 screws that secure the engine assembly

to the unit, located under the sump.

3. Remove the 4 screws that secure the front grill to the

cassette housing. (Figure 5)

4. Locate the cord and disconnect the wiring connections

noting their original locations.

NOTE: A flat head screwdriver can be used to gently

pry between the end of the connector and the switch to

release the wires.

5. With needle nose pliers, grasp the cord strain relief

grommet from inside the back of the bottom panel and

push while twisting to remove.