- ページ 6

ソフトウェア Epson PowerLite 8300i with EasyMP.net moduleのPDF クイックマニュアルをオンラインで閲覧またはダウンロードできます。Epson PowerLite 8300i with EasyMP.net module 20 ページ。 Release of check tool for network projectors v1.00 for windows
Epson PowerLite 8300i with EasyMP.net module にも： ユーザーマニュアル (42 ページ), 操作マニュアル (36 ページ), 操作マニュアル (47 ページ), クイックセットアップ (2 ページ), 製品サポート速報 (27 ページ), パーツリスト (1 ページ), 補足マニュアル (2 ページ), パンフレット＆スペック (2 ページ), ユーザーマニュアル (1 ページ), 製品サポート速報 (25 ページ), 製品サポート速報 (22 ページ), 製品サポート速報 (28 ページ), 製品サポート速報 (41 ページ), 製品サポート速報 (34 ページ), 製品サポート速報 (28 ページ), 製品サポート速報 (15 ページ), 製品サポート速報 (22 ページ), クイックセットアップ (2 ページ)

ページを印刷する
Epson PowerLite 8300i with EasyMP.net module クイックマニュアル
to
(if it's set to
Black
Blue
view images from a connected source after pressing
).
Mute
You can also view images on the monitor while the
projector is in standby mode (plugged in but not turned
on), if the
Standby Mode
in the Advanced1 menu.
ON

Displaying an Image

If you turn on your computer or video equipment before
turning on the projector, the projector will automatically
select the connected source. If you have multiple sources
connected, you may have to switch to the desired source
manually (see "Selecting the Image Source" at right).
Turning On the Projector
1. Remove the lens cap.
Caution: Do not use the projector with the lens cap in place.
The heat generated by the lens can damage the cap.
2. Plug in the projector.
3. Wait a few seconds until the P power light to turns orange.
4. Press the red P
Power
can also use the P
Power
Power
button
If you're using the remote control, make
sure batteries are installed and the power
switch on the side of the remote control
is turned on.
The P power light flashes green as the
projector warms up, and an image begins
to appear after about 30 seconds. When the power light
stops flashing and remains green (in about a minute), the
projector is ready for use.
Warning: Never look into the lens when the lamp is on. This
can damage your eyes.
or
, you won't be able to
Logo
setting has been set to
Network
button on top of the projector. You
button on the remote control.
Selecting the Image Source
A/V
You can use the source buttons either on the projector or the
remote control:
The projector has two
Use the
equipment connected to the Computer 1, Computer 2, and
DVI ports (or to switch to EasyMP.net, if that option has
been installed; see page 19).
Use the
connected to the Video, S-Video, and BNC ports.
The remote control has seven
switch between equipment connected to the port identified
on each button.
Note: You can preview all sources to help you select the desired
source (see page 6).
5/03
EPSON PowerLite 8300i Projector
buttons.
Source
button to switch between
Computer/DVI
button to switch between equipment
Video/BNC
Source
EPSON PowerLite 8300i Projector
buttons. Use them to
5
-