- ページ 14
テレビ Toshiba 20AF44のPDF サービスマニュアルをオンラインで閲覧またはダウンロードできます。Toshiba 20AF44 41 ページ。 Color television
Toshiba 20AF44 にも： オーナーズマニュアル (36 ページ), オーナーズマニュアル (36 ページ)
ページを印刷する
2-7: VERTICAL SIZE
1.
Receive the monoscope pattern.
2.
Using the remote control, set the brightness and
contrast to normal position.
3.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (07) on the remote control to
select "V.SIZE".
4.
Press the VOL. UP/DOWN button on the remote control
until the SHIFT quantity of the OVER SCAN on upside and
downside becomes 9 ± 2%.
5.
Receive a broadcast and check if the picture is normal.
2-8: VERTICAL LINEARITY
NOTE: Adjust after performing adjustments in section 2-7.
After the adjustment of Vertical Linearity, reconfirm
the Vertical Position and Vertical Size adjustments.
1.
Receive the monoscope pattern.
2.
Using the remote control, set the brightness and contrast
to normal position.
3.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (08) on the remote control to
select "V.LIN".
4.
Press the VOL. UP/DOWN button on the remote control
until the SHIFT quantity of the OVER SCAN on upside
and downside becomes minimum.
2-9: BRIGHT CENT
1.
Receive the monoscope pattern. (RF Input)
2.
Using the remote control, set the brightness and contrast
to normal position.
3.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (16) on the remote control to
select "BRI CENT".
4.
Press the VOL. UP/DOWN button on the remote control
until the white 15% is starting to be visible
5.
Receive the monoscope pattern. (Audio Video Input)
6.
Press the TV/VIDEO button on the remote control to set
to the AV mode. Then perform the above adjustments
2~4.
7.
Press the TV/VIDEO button on the remote control to set
to the CS mode.
8.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (16) on the remote control to
select "BRI CENT".
9.
Press the VOL. UP/DOWN button on the remote control
until the contrast step No. becomes "77".
10.
Receive a broadcast and check if the picture is normal.
ELECTRICAL ADJUSTMENTS
D-2
2-10: TINT/COLOR CENT
1.
Receive the color bar pattern. (RF Input)
2.
Connect the oscilloscope to TP806.
3.
Using the remote control, set the brightness, contrast,
color and tint to normal position.
4.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (24) on the remote control to
select "TINT".
5.
Press the VOL. UP/DOWN button on the remote control
until the section "A" becomes a straight line
(Refer to Fig. 2-1).
6.
Connect the oscilloscope to TP804.
7.
Press the CH DOWN button 2 times to set to "COL.
CENT" mode.
8.
Adjust the VOLTS RANGE VARIABLE knob of the
oscilloscope until the range between white 100% and
0% is set to 5 scales on the screen of the oscilloscope.
9.
Press the VOL. UP/DOWN button on the remote control
until the red color level is adjusted to 120 ± 10% of the
white level. (Refer to Fig. 2-2)
10.
Receive the color bar pattern. (Audio Video Input)
11.
Press the TV/VIDEO button on the remote control to set
to the AV mode. Then perform the above adjustments
2~9.
12.
Press the TV/VIDEO button on the remote control to set
to the CS mode.
13.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (24) on the remote control to
select "TINT".
14
Press the VOL. UP/DOWN button on the remote control
until the contrast step No. becomes "58".
15.
Press the CH DOWN button 2 times to set to
"COL.CENT" mode.
16.
Press the VOL. UP/DOWN button on the remote control
until the contrast step No. becomes "71".
17.
Receive a broadcast and check if the picture is normal.
White 100% RED Level
"A"
Fig. 2-1
100%
Fig. 2-2