- ページ 24
ステレオシステム Philips 3 CD CHANGER PRO LOGIC FWP73P37のPDF ユーザーマニュアルをオンラインで閲覧またはダウンロードできます。Philips 3 CD CHANGER PRO LOGIC FWP73P37 31 ページ。 Cd mini system
Philips 3 CD CHANGER PRO LOGIC FWP73P37 にも： 仕様 (2 ページ)
ページを印刷する
RECORDING
24
Dubbing tapes
(from tape deck 2
to tape deck 1)
1 Load the prerecorded tape into tape
deck 2 and a blank tape into tape
deck 1.
• Make sure both tapes have their full
spool to the left.
2 Press PAUSE on tape deck 1.
3 Press RECORD on tape deck 1.
4 Press PLAYÉ on tape deck 2.
™ The
starts flashing.
REC
• Recording will start automatically.
5 Press STOP•OPEN on tape deck 1
and tape deck 2 to stop dubbing.
Notes:
– At the end of side A, flip the tapes to
side B and repeat the procedure.
– Dubbing of tapes is only possible from
tape deck 2 to tape deck 1.
– To ensure good dubbing, use tapes of
the same length.
Recording from other
sources
(only on tape deck 1)
1 Load a blank tape into tape deck 1.
2 Press CD, TUNER or AUX.
• Start playback of the selected source.
3 Press RECORD on tape deck 1 to
start recording.
™ The
starts flashing.
REC
4 Press PAUSE to interrupt
recording.
5 Press STOP•OPEN on tape deck 1
to stop recording.
Note:
– During recording, it is not possible to
listen to another sound source.
CLOCK
MINI HIFI SYSTEM
PROGRAM
SHUFFLE
REPEAT
TIMER
REC
NEWS
T.A.
AM
MW
FM
LW
60Hz
250Hz
500Hz
1KHz
STANDBY
ON
CLOCK/
TIMER
CD1 • 2 • 3
FM • AM
CD
TUNER
PROG
SEARCH • TUNING
STOP • CLEAR
PLAY PAUSE
UP
SOUND NAVIGATION
SOUND
DOWN
DIGITAL SOUND
CONTROL
View Clock
You can view the clock (if it is set) if the
system is in Standby mode or when any
sound source is selected (CD, TUNER,
etc.). The clock will be displayed for
about seven seconds.
• Press CLOCK/TIMER briefly.
™ "PM 10:38 or 22:38 " (the
current time) will be displayed
depending on whether you have
selected 12- or 24-hour mode.
™ "--: : : : : --" will be displayed if the
clock is not set.
C
C
C
STEREO
BACK
FRONT
HSD
L
L
L
R
R
R
4KHz
8KHz
2KHz
PRO LOGIC
PRO LOGIC
PRO LOGIC
DOLBY B
S
S
S
S
S
S
NR
RDS
NEWS!
TAPE 1 • 2
VIDEO
TAPE
AUX
PRESET
PREV
NEXT
VOLUME
DYNAMIC BASS
BOOST
Clock Setting
The clock can be set in either 12- or
24-hour mode, e.g. "AM 12:00" or
"00:00". Before setting the clock, you
must be in the View Clock mode.
1 Press CLOCK/TIMER to select
clock mode.
2 Press PROG (on the system only) to
select 12- and 24- hour mode.
™ If 12-hour mode is selected, "AM
12:00" starts flashing.
™ If 24-hour mode is selected,
"00:00" starts flashing.
3 Set the hour with à or á on the
system.
4 Set the minute with í or ë on
the system.
5 Press CLOCK/TIMER again to
store the setting.
™ The clock starts.
3139 116 19511 ( ENG)