- ページ 20
ステレオシステム Philips 3 CD CHANGER WITH DOLBY PRO LOGIC PROCESSOR FWP88CのPDF マニュアルをオンラインで閲覧またはダウンロードできます。Philips 3 CD CHANGER WITH DOLBY PRO LOGIC PROCESSOR FWP88C 31 ページ。 3 cd changer with dolby® pro logic processor, five loudspeakers, 320 watts total power
Philips 3 CD CHANGER WITH DOLBY PRO LOGIC PROCESSOR FWP88C にも： ユーザーマニュアル (31 ページ), 仕様 (2 ページ)
ページを印刷する
All manuals and user guides at all-guides.com
TUNER
MINI HIFI SYSTEM
STANDBY
ON
POWER SAVE
IR SENSOR
CD 1•2•3
BAND
C1 • 2 • 3
CD
BAND
TUNER
SEARCH•TUNING
STOP•CLEAR
CLOCK/
PROG
DIM
TIMER
BASS
wOOx
PLUS
TECHNOLOGY
Note:
– For 'EASY SET' feature, please refer to
page 13.
Tuning to radio stations
1 Press TUNER (BAND) to select TUNER
mode.
™ "TUNER" will be displayed.
A few seconds later, the current radio
frequency will be displayed.
2 Press TUNER (BAND) again to select
the desired waveband : FM, MW or LW.
3 Press à or á for more than one
second, then release.
™ The display will show "SEARCH"
until a radio station with sufficient
signal strength is found.
20
pg 01-31/P88/22-Eng
20
DOLBY B NR
LEFT
CENTER
RIGHT
NEWS/TA
SURR
SURR
PRO LOGIC
RDS
TAPE 1•2
CDR/DVD
CD TEXT
TAPE
CDR
AUX
PRESET
PLAY PAUSE
PREV
SIDE
NEXT
DUB
A. REV
RECORD
(HSD)
TREBLE
LEVEL
Notes:
• Repeat this procedure until the desired
– You can cancel the automatic
station is reached.
• To tune to a weak station, briefly press
à or á repeatedly until the display
– If you want to reserve a section of
shows the desired frequency and/or
when the best reception has been
obtained.
Storing Preset Stations
You can store up to 40 radio stations in the
Manual programming
memory. When a preset radio station is
1 Press TUNER (BAND).
selected, the preset number appears next
2 Press TUNER (BAND) again to select
to the frequency on the display.
3 Press PROG for less than one second.
Automatic programming
1 Press TUNER (BAND).
2 Press PROG for more than one second.
™ The
starts flashing and
PROGRAM
"AUTO" will be displayed.
4 Press à or á to tune to the desired
™ The system will start searching for all
radio stations with RDS and then
frequency.
followed by radio stations on FM,
• If you wish to store the radio station to
another preset number, press 4 or 3
MW and LW band respectively.
™ All available stations will be stored
(or Digit 0-9 on the remote control) to
automatically. The frequency and
select the desired preset number.
preset number will be displayed
5 Press PROG again.
briefly.
™ The
™ The system will stop searching when
radio station will be stored.
all the available radio stations are
• Repeat steps 3 – 5 to store other preset
stored or when the memory for 40
radio stations.
preset radio stations is used.
Notes:
™ The system will remain tuned to the
– When 40 radio stations are stored and
last stored preset radio station.
you attempt to store another radio
station, the display will show
" PROGRAM FULL ". If you want to
programming by pressing PROG or Ç
change an existing preset number,
(on the system only).
repeat steps 3 – 5.
– You can cancel manual programming by
preset numbers, for example preset
pressing Ç (on the system only).
numbers 1 to 9, select preset 10 before
– During programming, if no button is
starting automatic programming, only
pressed within 20 seconds, the system
the preset numbers 10 to 40 will be
will exit program mode automatically.
programmed.
Tuning to Preset Radio
Stations
• Press 4 or 3 (or Digit 0-9 on the
the desired waveband : FM, MW or LW.
remote control) to select the desired
preset number.
™ The
starts flashing.
PROGRAM
™ The preset number, radio frequency,
™ The next available preset number will
and waveband appear on the display.
be displayed for selection.
3/6/00, 1:27 PM
disappears and the
PROGRAM
3139 116 19721