- ページ 27

プロジェクター Toshiba TLP-S201のPDF オーナーズマニュアルをオンラインで閲覧またはダウンロードできます。Toshiba TLP-S201 36 ページ。 3lcd data projector (xga / svga / high brightness / with pc card slot & document camera)

ページを印刷する

Using the menus

You can call up on-screen menus, and conduct a number of adjustments and settings,

using the operation buttons

p.16

on the control panel (main unit side) and remote control.

How to use the menus

The menu shown below is only for operation

instructions and might be different from the actual

display.

2. Select a Category

To PC card setting menu

p.54

To Image adjustment menu

p.53

To Display setting menu

p.54

To Default setting menu

p.53

3. Adjustments & Settings

Item

Adjustment/Setting Value

These marks signify the

items can be adjusted/set

by using

These marks signify an

item can be switched by

using

The figure shows a typical example.

As the display may differ depending

on the item, use the following pages

as a reference.

These marks signify the items can be selected from

the list by using

After an item selected, apply it by pressing

4. Back

Note

• Menu adjustments and settings (except Lamp power

turned off via the ON/STANDBY button. If the power cord is unplugged before this, or the

power goes out, then the data will not be saved.

1. Start

Display the Setting display menu

Displays the

current adjust-

ment/setting of

each category

5. To Finish

Finish via the Status

display menu.

This mark signfy that

there are options.

Press

to display a

list of options.

To Status display

p.32

6. End

The menu disappears

p.53

) are saved when the power is

The image adjustment menu

Use this menu to adjust image-related items.

Items Items that can be adjusted are marked with "Yes", and those that cannot are marked

with "No".

Item

Description

Contrast

Lower

Higher

Brightness Darker

Brighter

Color

Lighter

Deeper

Tint

[Note 1]

Reddish

Greenish

Sharpness Softer

Sharper

R-level

Less red

More red

G-level

Less green

More green

B-level

Less blue

More blue

Up/down shift

[Note 2]

Shift down

Shift up

Notes

1: Tint can only be adjusted when Video mode

2: Up/down shift can only be adjusted when Screen size

The default setting menu

This menu shows placement status and other settings.

Item

Projection

Set projection mode in accordance with Placement Style

mode

(Placed

on floor)

No signal

Set the time to wait after signal input stops until turning off the power:

power off

Off (not turned off)

Power on

Set whether to turn on the power when the ON/STANDBY button is pressed

(Manual), or when the power cord is plugged in (Auto). Manual

Lamp power

[Note 1]

Set the lamp power

Standby mode

[Note 2]

Set standby mode according to functions used Standard

Notes

1: When lamp power is set to low, the screen becomes a little darker, but the cooling fan noise gets

quieter. This setting will be cleared when you turn the power off. The setting will be back to

"Standard" when the power is turned on next time.

2: The Standby mode function is only available with models equipped with a PC card slot

Notes

• Note that if Power on is set to Auto, then if the power cord is plugged in when power is

restored after a power outage, the projector power will come on.

• Even if Power on is set to Auto, press the ON/STANDBY button to turn off the power.

Unplugging the power cord to cut off the power will shorten the life of the lamp.

Video

Computer Y/P

PC Card Camera

S-video

Yes

p.29

is NTSC or NTSC4.43.

p.54

is Wide.

Description

p.21

(Hung from

(Back hung

(Rear)

ceiling)

from ceiling)

1 min

2 min

...

60 min

Standard

Low

Economy

p.39

Yes

Auto