- ページ 4

ヒーター Dimplex ARC10AのPDF ユーザーマニュアルをオンラインで閲覧またはダウンロードできます。Dimplex ARC10A 8 ページ。 Architectural air curtains
Dimplex ARC10A にも：ユーザーマニュアル (9 ページ)

ページを印刷する

Architectural Air Curtains

Models : ARC10E, ARC15E, ARC20E, ARC10W, ARC15W, ARC20W, ARC10A, ARC15A & ARC20A

IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE

IMPORTANT SAFETY ADVICE

DO NOT COVER OR OBSTRUCT the air inlet or outlet grille.

ENSURE THE APPLIANCE IS EARTHED.

Do not use this heater in areas where excessive dust exists.

Do not use this heater with young children unattended.

This appliance is not intended for use by children or other

persons without assistance or supervision if their physical,

sensory or mental capabilities prevent them from using it

safely. Children should be supervised to ensure that they

do not play with the appliance.

The heater carries the Warning symbol indicating that

it must not be covered.

Warning: In order to avoid overheating, do not cover the

heater.

This heater must not be located immediately above or below

a fixed socket outlet or connection box.

Always disconnect supply before working on the product.

This appliance should only be connected to the fixed wiring

of the premises by means of conduit.

This product should be mounted safely to solid wall, floor

or ceiling surfaces only.

If mounting the appliance horizontally it should not be

mounted less than 1.8m from the floor.

This product must not be subjected to water spray or

immersion.

Ensure the supply cables are of adequate current carrying

capacity and are protected by a suitable fuse.

This appliance should not be mounted in a toilet or

washroom.

Ensure proper manual handling procedures are observed

at all times.

WARNING: Isolate electrical supply to ALL modular linked

units when carrying out maintenance.

Models

Model

Heat

Electrical

output

AMBIENT

ARC10A

220-240V ~1PN

n/a

ARC15A

220-240V ~1PN

n/a

ARC20A

220-240V ~1PN

n/a

ELECTRICALLY HEATED

ARC10E

6.0 / 12.0

380-415V ~3PN

ARC15E

9.0 / 18.0

380-415V ~3PN

ARC20E

12.0 / 24.0

380-415V ~3PN

WATER HEATED (at 82/71 °C - LPHW)**

ARC10W

220-240V ~1PN

ARC15W

220-240V ~1PN

ARC20W

220-240V ~1PN

Electrical

The installation of this appliance should be carried out by a

competent electrician and be in accordance with the current IEE

wiring regulations.

Weight

Electrical

Supply

load

(per phase)

1.5

2.3

82.5

3.0

110

120

1.5

2.3

130

Fixing Positions

This appliance may be either fixed to a ceiling - see Fig. 1 or floor

mounted see Fig. 2 using an appropriate foot.

A minimum distance of 500mm is required from top of the

appliance to the ceiling (see Fig. 1) and also the distance between

the bottom of the appliance and the top of the door should be

kept to a minimum (see 'C' in Fig. 1).

To open the appliance, remove the inlet grilles ('x' in Fig. 3)

Remove the front panel ('z' in Fig. 3).

Horizontal Mounting

By using the fixing holes in the top of the air curtain, attachment

to a ceiling over the product can be achieved using suitable M10

threaded steel rod or similar supports of sufficient strength -

see 's' in Fig. 1.

Vertical Mounting

The architectural range of air curtains can be vertically mounted

using a suitable floor foot (Ref: ARCVMF). Contact Dimplex or

your service agent for further information. Refer to Fig. 2 for fixing

details.

Electrical connection

All products are fitted with a microprocessor control. Electrical

power and control connections are made as shown in Fig. 6 & 7.

A suitable local isolating switch must be provided in the electrical

supply circuit with at least 3mm clearance on each pole. In

order to access the electrical connections, remove the inlet grilles

(see 'x' in Fig. 3). Remove the front panel (see 'z' in Fig. 3) and

also remove the mains cover plate (see 'y' in Fig. 3).

ARC Electric Models

Feed an appropriate supply cable as shown in Fig. 4 and attach

to the terminal block (see 'a' in Fig. 4).

Note: Ensure that cables are secured to the cable tray with fixing

ties to avoid contact with the elements.

ARC Water/Ambient Models

Feed an appropriate supply cable as shown in Fig. 5 and attach

to the terminal block (see 'a' in Fig. 5).

A suitable cable for a switch panel (kit ref. - CABC1 for electrically

heated models or CABC2 for water heated/ambient models)

Recom-

can be similarly introduced through the top panel and connected

mended

height

to the circuit board.

If the unit is to be operated in conjunction with a door switch, a

normally closed switch should be wired (see 'D' in Fig. 6 & 7) as

appropriate - see also 'Switch Panel Instructions'.

3.75

If the unit is to be connected to a Building Energy Management

3.75

System, connections to be made (see 'G' in Fig. 6 & 7) as

3.75

appropriate.

Ensure that the air curtain is securely fastened in position and

3.75

that the supply cables are firmly clamped before operating the

3.75

appliance.

3.75

Water connection

3.75

Models designed for use in conjunction with a low pressure hot

3.75

water supply should be individually connected (in a parallel

3.75

circuit) to the flow and return pipe-work.

Connections (see 'a' in Fig. 8) are ¾" BSPT and isolation valves

(see 'b' in Fig. 8) should be fitted as close to the air curtain

connection points as possible. Care should be taken to release

as much air as possible to prevent air locks.

Maximum water supply conditions are 100ºC and 10 bar

(1.03MPa).