- ページ 6

ヒーター Dimplex CAB15ARのPDF ユーザーマニュアルをオンラインで閲覧またはダウンロードできます。Dimplex CAB15AR 9 ページ。 Compact air curtains
Dimplex CAB15AR にも：マニュアル (12 ページ), マニュアル (8 ページ)

ページを印刷する

Dimplex Compact Air Curtains

Models :

IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE

IMPORTANT SAFETY ADVICE

DO NOT COVER OR OBSTRUCT the air inlet or outlet

grille.

ENSURE THE APPLIANCE IS EARTHED.

Do not use this heater in areas where excessive dust

exists.

This heater must not be located immediately above or

below a ﬁ xed socket outlet or connection box.

Always disconnect supply before working on the

product.

This appliance should only be connected to the ﬁ xed

wiring of the premises by means of conduit.

This product should only be mounted safely to solid

ceiling surfaces.

This product must not be subjected to water spray or

immersion.

Ensure the supply cables are of adequate current

carrying capacity and are protected by a suitable fuse.

If the appliance is mounted in a toilet or washroom, the

appliance should be mounted such that no part of it can

be touched by a person using a ﬁ xed bath or shower.

If the appliance is mounted in a toilet or washroom

an isolating switch must be provided outside the

washroom adjacent to the entrance door.

This appliance is not intended for use by persons

(including children) with reduced physical, sensory

or mental capabilities, or lack of experience and

knowledge, unless they have been given supervision or

instruction concerning use of the appliance by a person

responsible for their safety.

WARNING: Isolate electrical supply to ALL modular

linked units when carrying out maintenance.

Models

Model

Heat Output

Electrical Supply

AMBIENT / COLD STORE

CAB10AR

n/a

220-240V ~1PN

CAB15AR

n/a

220-240V ~1PN

ELECTRICALLY HEATED

CAB10ER

4.5 / 9.0

380-415V ~3PN

CAB15ER

6.75 / 13.5

380-415V ~3PN

WATER HEATED (at 82/71 °C - LPHW)**

CAB10WR

9.0

220-240V ~1PN

CAB15WR

13.5

220-240V ~1PN

This range of air curtains are speciﬁ cally designed to be

recessed into ceiling spaces and above suspended ceilings.

Electrical

The installation of this appliance should be carried out by a

competent electrician and be in accordance with the current IEE

wiring regulations.

CAB10ER, CAB10WR, CAB10AR

CAB15ER, CAB15WR & CAB15AR

Electrical

Weight

Load

(per phase)

0.3

20.5

0.5

29.5

0.3

0.5

32.5

Fixing Positions

This appliance must be mounted to a suitable ceiling - see Fig.

1 for ﬁ xing dimensions and Fig. 5, 6, or 7 for mounting positions

and 'Mounting' sections below for ﬁ xing details. This appliance

should not be mounted less than 1.8m from the ﬂ oor.

Mounting into a Standard Ceiling Void

1. Side Fixings - Using a suitable ceiling surface, mark off and

drill for M8 drops rods. Dimensions can be found on Fig.1. Cut

the M8 drop rods to the desired length, taking note of the ﬁ nal

position of the appliance relative to the distance to the mounting

surface. Mount the drop rods to the ceiling surface. Remove the

ceiling tiles on the appliance. (see Fig. 2) Using suitable lifting

equipment raise up the appliance to the drop rods as shown in

Fig. 5. Connect the appliance to the drop rods using standard M8

lock nuts and washers.

2. Top Mounted Inserts - If a suitable (unistrut) structure is

available, mark off and drill for M8 threaded bolts. Insert the bolts

down through the structure. Dimensions can be found on Fig.

1. Using suitable lifting equipment raise up the appliance to the

bolts. Screw the bolts into the threaded inserts on the top of the

appliance, and tighten securely.

Electrical connection

All products are ﬁ tted with a microprocessor control. Electrical

power and control connections are made as shown in Fig. 4. A

suitable local isolating switch must be provided in the electrical

supply circuit with at least 3mm clearance on each pole. In order

to access the electrical connections, remove the outlet grilles ('x'

in Fig. 2) by undoing the four fasteners in each tile. For the Water

heated and Ambient models only, the pressure plate must also be

removed.

Max

All Electric Models

Installed

height

top panel, feed an appropriate supply cable (see 'a' in Fig. 4A)

through a suitable cable gland (not supplied) ﬁ tted in the top

panel and attach to the terminal block (see 'b' in Fig. 4A).

3.0

All Water heated and Ambient Models

removed a 'knock out' in the top panel, feed an appropriate

supply cable (see 'a' in Fig.4B) through a suitable cable gland

3.0

(not supplied) ﬁ tted in the top panel and attach to the PCB (see

3.0

'b' in Fig. 4B).

3.0

- Having removed a 'knock out' in the

- Having