- ページ 4

カーレシーバー Pioneer AVIC-Z720DABのPDF インストレーション・マニュアルをオンラインで閲覧またはダウンロードできます。Pioneer AVIC-Z720DAB 17 ページ。 Navigation av system
Pioneer AVIC-Z720DAB にも：クイック・スタート・マニュアル (16 ページ), システム・ファームウェアのアップデート手順 (5 ページ)

ページを印刷する

1. Rear Panel (Main Terminals)

OF THE VEHICLE'S ANTILOCK BRAKING

SYSTEM, AUTOMATIC TRANSMISSION

AND SPEEDOMETER INDICATION.

CAUTION

It is strongly suggested that the speed

pulse wire be connected for accuracy of

navigation and better performance.

To power supply

Depending on the kind of vehicle, the

function of 2* and 4* may be different.

In this case, be sure to connect 1* to 4*

and 3* to 2*.

Yellow (2*)

Back-up (or accessory)

Yellow (1*)

To terminal supplied with power

regardless of ignition switch position.

Red (4*)

Accessory (or back-up)

Red (3*)

Connect to terminal controlled by

ignition switch (12 V DC).

Connect leads of the same colour to

each other.

Orange/white

To lighting switch terminal.

Black (earth)

To vehicle (metal) body.

Blue/white (5*)

The pin position of the ISO connector

will differ depending on the type of

vehicle. Connect 5* and 6* when Pin 5 is

an aerial control type. In another type of

vehicle, never connect 5* and 6*.

Blue/white (6*)

Connect to auto-aerial relay control

terminal (max. 300 mA 12 V DC).

Blue/white

Connect to system control terminal of

the power amp (max. 300 mA 12 V DC).

Violet/white

This is connected so that this product

can detect whether the vehicle is

moving forwards or backwards.

Connect the violet/white lead to the

lead whose voltage changes when the

gearstick is put in reverse. Unless

connected, the sensor may not detect

your vehicle travelling forwards/

backwards properly, and thus the

position of your vehicle detected by the

sensor may be misaligned from the

actual position.

When you use a rear view camera,

please make sure to connect this lead.

Otherwise you cannot switch to the rear

view camera picture.

Pink (CAR SPEED SIGNAL INPUT)

This product is connected here to

detect the distance the vehicle travels.

Always connect the vehicle's speed

detection circuit. Failure to make this

connection will increase errors in the

vehicle's location display.

Light green

Used to detect the ON/OFF status of the

handbrake. This lead must be

connected to the power supply side of

the handbrake switch.

If this connection is made incorrectly

or omitted, certain functions of this

product will be unusable.

Connection method

Clamp the lead (1) then clamp firmly

with needle-nosed pliers (2).

Power supply side

Handbrake switch

Earth side

Speaker leads

White: Front left + or high range left +

White/black: Front left – or high range

left –

Grey: Front right + or high range right +

Grey/black: Front right – or high range

right –

Green: Rear left + or middle range left +

Green/black: Rear left – or middle range

left –

Violet: Rear right + or middle range

right +

Violet/black: Rear right – or middle

range right –

ISO connector

In some vehicles, the ISO connector

may be divided into two. In this case, be

sure to connect to both connectors.

NOTES

• The position of the speed detection

circuit and the position of the handbrake

switch vary depending on the vehicle

model. For details, consult your

authorised Pioneer dealer or an

installation professional.

• When a subwoofer is connected to this

product instead of a rear speaker, change

the rear output setting in the initial

setting. The subwoofer output of this

product is monaural.

• When using a subwoofer of 2 Ω, be sure

to connect the subwoofer to the violet

and violet/black leads of this unit. Do not

connect anything to the green and

green/black leads.