- ページ 11

カーレシーバー Pioneer DEH-6400BTのPDF オーナーズマニュアルをオンラインで閲覧またはダウンロードできます。Pioneer DEH-6400BT 25 ページ。 Cd rds receiver
Pioneer DEH-6400BT にも：操作マニュアル (36 ページ), クイック・スタート・マニュアル (8 ページ)

ページを印刷する

Operating this unit

FAD/BAL (fader/balance adjustment)

1 Press M.C. to display the setting mode.

2 Press M.C. to cycle between fader (front/rear)

and balance (left/right).

3 Turn M.C. to adjust speaker balance.

When the rear output and RCA output setting

are SW, you cannot adjust front/rear speaker

balance. Refer to REAR-SP (rear output setting)

on this page. Refer to PREOUT (preout setting)

on this page.

PRESET EQ (equalizer recall)

1 Press M.C. to display the setting mode.

2 Turn M.C. to select the equalizer.

DYNAMIC VOCAL NATURAL CUSTOM

FLAT POWERFUL

3 Press M.C. to confirm the selection.

TONE CTRL (equalizer adjustment)

Adjusted equalizer curve settings are stored in

CUSTOM.

1 Press M.C. to display the setting mode.

2 Press M.C. to select BASS (bass)/MID (mid)/

TREBLE (treble).

3 Turn M.C. to adjust the level.

Adjustment range: +6 to –6

LOUD (loudness)

Loudness compensates for deficiencies in the low-

frequency and high-frequency ranges at low vol-

ume.

1 Press M.C. to select the desired setting.

OFF (off) LOW(low) HI (high)

SUB.W (subwoofer on/off setting)

This unit is equipped with a subwoofer output

which can be turned on or off.

1 Press M.C. to select the desired setting.

NOR (normal phase) REV (reverse phase)

OFF (subwoofer off)

SUB.W CTRL (subwoofer adjustment)

The cut-off frequency and output level can be ad-

justed when the subwoofer output is on.

Only frequencies lower than those in the selected

range are outputted from the subwoofer.

When you select OFF in SUB.W, you cannot se-

lect this function. For details, refer to SUB.W

(subwoofer on/off setting) on this page.

1 Press M.C. to display the setting mode.

2 Press M.C. to cycle between the cut-off fre-

quency and output level of the subwoofer.

Cut-off frequency (Cut-off frequency display

flashes.) Output level (Output level display

flashes.)

3 Turn M.C. to select the desired setting.

Cut-off frequency: 50HZ 63HZ 80HZ

100HZ 125HZ

Output level: –24 to +6

SLA (source level adjustment)

SLA (Source level adjustment) lets you adjust the

volume level of each source to prevent radical

changes in volume when switching between sour-

ces.

Settings are based on the FM volume level,

which remains unchanged.

The AM volume level can also be adjusted with

this function.

When selecting FM as the source, you cannot

switch to SLA.

1 Press M.C. to display the setting mode.

2 Turn M.C. to adjust the source volume.

Adjustment range: +4 to –4

3 Press M.C. to confirm the selection.

Initial settings

Press and hold SRC/OFF until the unit

turns off.

Press M.C. and hold until function name

appears in the display.

Operating this unit

Turn M.C. to select the initial setting.

After selecting, perform the following proce-

dures to set the initial setting.

CLOCK SET (setting the clock)

1 Press M.C. to display the setting mode.

2 Press M.C. to select the segment of the clock

display you wish to set.

Hour Minute

3 Turn M.C. to adjust the clock.

AUX (auxiliary input)

Activate this setting when using an auxiliary de-

vice connected to this unit.

1 Press M.C. to turn AUX on or off.

USB PNP (plug and play)

This setting allows you to switch your source to

USB/iPod automatically.

1 Press M.C. to turn the plug and play function

on or off.

ON When a USB storage device/iPod is con-

nected, depending on the type of device, the

source is automatically switched to USB/iPod

when you turn on the engine. If you disconnect

your USB storage device/iPod, this unit s

source is turned off.

OFF When a USB storage device/iPod is con-

nected, the source is not switched to USB/

iPod automatically. Please change the source

to USB/iPod manually.

REAR-SP (rear output setting)

The rear speaker leads output can be used for full-

range speaker or subwoofer connection.

If you switch to SW, you can connect a rear speak-

er lead directly to a subwoofer without using an

auxiliary amp.

Initially, REAR-SP is set for rear full-range speaker

connection (FUL).

1 Press M.C. to select the desired setting.

FUL SW

Even if you change this setting, there will

be no output if you select OFF in SUB.W

(Refer to SUB.W (subwoofer on/off setting)

on this page).

If you change this setting, subwoofer out-

put in the audio menu will return to the fac-

tory settings.

PREOUT (preout setting)

The RCA outputs can be used for rear speaker or

subwoofer connection.

If you switch to SW, you can connect a rear speak-

er lead directly to a subwoofer without using an

auxiliary amp.

Initially, PREOUT is set for rear full-range speaker

connection (SW).

1 Press M.C. to select the desired setting.

SW REA

Even if you change this setting, there will

be no output if you select OFF in SUB.W

(Refer to SUB.W (subwoofer on/off setting)

on this page).

If you change this setting, subwoofer out-

put in the audio menu will return to the fac-

tory settings.

DEMO (demo display setting)

1 Press M.C. to turn the demo display on or off.

SCROLL (scroll mode setting)

Section