- ページ 2
カーレシーバー Pioneer Super Tuner III DEH-P90HDDのPDF インストレーション・マニュアルをオンラインで閲覧またはダウンロードできます。Pioneer Super Tuner III DEH-P90HDD 6 ページ。 Pioneer deh-p90hdd: install guide
ページを印刷する
Installation
Note:
•
This unit must be installed after pulling the auto-
• Before finally installing the unit, connect the
equalizing mike jack out of the console box, so
wiring temporarily, making sure it is all connected
that the mike can be plugged in or pulled out even
up properly, and the unit and the system work
after this unit has been installed.
properly.
•
The cords must not cover up the area shown in
• Use only the parts included with the unit to ensure
Fig. 2. This is so the amplifiers can radiate freely.
proper installation. The use of unauthorized parts
can cause malfunctions.
• Consult with your nearest dealer if installation
requires the drilling of holes or other modifications
of the vehicle.
• Install the unit where it does not get in the driver's
way and cannot injure the passenger if there is a
sudden stop, like an emergency stop.
Do not close this area.
• The semiconductor laser will be damaged if it
overheats, so don't install the unit anywhere hot
— for instance, near a heater outlet.
• If installation angle exceeds 30° from horizontal,
the unit might not give its optimum performance.
(Fig. 3)
30
Fig. 3
• This unit and the GPS antenna of the navigation
unit should be set as far apart as possible. If they
are too close, this unit and the navigation unit may
not operate correctly.
• Do not install the power box near doors where
rainwater could splash onto it.
• As the power box can heat up, it should never be
installed in the following locations:
– where it could come into contact with car
wiring or equipment
– where it would easily come into contact with
passengers.
DIN Front/Rear-mount
This unit can be properly installed either from "Front" (conventional DIN Front-mount) or
"Rear" (DIN Rear-mount installation, utilizing threaded screw holes at the sides of unit
chassis). For details, refer to the following illustrated installation methods.
DIN Front-mount
Installation with the rubber bush (Fig. 5)
Holder
After inserting the holder into the dash-
board, then select the appropriate tabs
according to the thickness of the dash-
Fig. 4
Dashboard
board material and bend them.
(Install as firmly as possible using the
182
top and bottom tabs. To secure, bend
the tabs 90 degrees.)
53
Rubber bush
Screw
Installation without the rubber bush (Fig. 6)
Dashboard
Nut (5 mm)
Drill a 5.5 – 6.0 mm
diameter hole.
Strap
Be sure to use the strap to secure the back
of the unit in place. The strap can be bent
Screw (5 16 mm)
by hand to the desired angle.
Screw
Nut (5 mm)
Removing the Unit (Fig. 7) (Fig. 8)
Frame
Insert the release pin into the hole in
the bottom of the frame and pull out
to remove the frame.
(When reattaching the frame, point
Fig. 5
the side with a groove downwards
and attach it.)
Insert the supplied extraction keys
into the unit, as shown in the figure,
until they click into place. Keeping
the keys pressed against the sides of
the unit, pull the unit out.
A Title (English)
DIN Rear-mount
Installation using the screw holes on the side of the unit
1. Remove the frame. (Fig. 9)
Frame
Insert the release pin into the hole in
the bottom of the frame and pull out
to remove the frame.
(When reattaching the frame, point
the side with a groove downwards
and attach it.)
Fig. 6
2. Fastening the unit to the factory radio mounting bracket.
(Fig. 10) (Fig. 11)
Select a position where the screw holes of the bracket and
the screw holes of the head unit become aligned (are fitted),
and tighten the screws at 2 places on each side. Use either
binding screws (5 8 mm) or flush surface screws
(5 8 mm), depending on the shape of the screw holes in
.
the bracket
Fig. 7
Screw
Factory radio mounting bracket
Fig. 8
<ENGLISH>
Fig. 9
Fig. 10
Dashboard or Console
Fig. 11