カーレシーバー Pioneer Super Tuner IIID DEH-P5800MPのPDF インストレーション・マニュアルをオンラインで閲覧またはダウンロードできます。Pioneer Super Tuner IIID DEH-P5800MP 6 ページ。 Owner's manual
Pioneer Super Tuner IIID DEH-P5800MP にも：オーナーズマニュアル (34 ページ), 操作マニュアル (38 ページ)

ページを印刷する

DEH-P5800MP

This product conforms to CEMA cord colors.

Le code de couleur des câbles utilisé pour ce produit est

conforme à CEMA.

Printed in Thailand

Imprimé en Thaïlande

<XRD7096-A/N> UC

Connecting the Units

Note:

• This unit is for vehicles with a 12-volt battery and

• When an external power amp is being used with

negative grounding. Before installing it in a recre-

this system, be sure not to connect the blue/white

ational vehicle, truck, or bus, check the battery

lead to the amp's power terminal. Likewise, do not

voltage.

connect the blue/white lead to the power terminal

• To avoid shorts in the electrical system, be sure to

of the auto-antenna. Such connection could cause

disconnect the ≠ battery cable before beginning

excessive current drain and malfunction.

installation.

• To avoid a short-circuit, cover the disconnected

• Refer to the owner's manual for details on

lead with insulating tape. Insulate the unused

connecting the power amp and other units, then

speaker leads without fail. There is a possibility of

a short-circuit if the leads are not insulated.

make connections correctly.

• Secure the wiring with cable clamps or adhesive

• To prevent incorrect connection, the input side of

the IP-BUS connector is blue, and the output side

tape. To protect the wiring, wrap adhesive tape

is black. Connect the connectors of the same

around them where they lie against metal parts.

colors correctly.

• Route and secure all wiring so it cannot touch any

• If this unit is installed in a vehicle that does not

moving parts, such as the gear shift, handbrake and

have an ACC (accessory) position on the ignition

seat rails. Do not route wiring in places that get

switch, the red lead of the unit should be connected

hot, such as near the heater outlet. If the insulation

of the wiring melts or gets torn, there is a danger of

to a terminal coupled with ignition switch ON/OFF

the wiring short-circuiting to the vehicle body.

operations. If this is not done, the vehicle battery

may be drained when you are away from the vehi-

• Don't pass the yellow lead through a hole into the

cle for several hours. (Fig.1)

engine compartment to connect to the battery. This

will damage the lead insulation and cause a very

dangerous short.

• Do not shorten any leads. If you do, the protection

circuit may fail to work when it should.

• Never feed power to other equipment by cutting

the insulation of the power supply lead of the unit

and tapping into the lead. The current capacity of

the lead will be exceeded, causing overheating.

ACC position

No ACC position

• When replacing the fuse, be sure to only use a fuse

of the rating prescribed on this unit.

• Since a unique BPTL circuit is employed, never

wire so the speaker leads are directly grounded or

the left and right ≠ speaker leads are common.

• The black lead is ground. Please ground this lead

• Speakers connected to this unit must be high-

separately from the ground of high-current prod-

power with minimum rating of 50 W and imped-

ucts such as power amps.

ance of 4 to 8 ohms. Connecting speakers with out-

If you ground the products together and the ground

put and/or impedance values other than those

becomes detached, there is a risk of damage to the

noted here may result in the speakers catching fire,

products or fire.

emitting smoke or becoming damaged.

• When this product's source is switched ON, a con-

trol signal is output through the blue/white lead.

• Cords for this product and those for other products

Connect to an external power amp's system remote

may be different colors even if they have the same

control or the car's Auto-antenna relay control ter-

function. When connecting this product to another

minal (max. 300 mA 12 V DC). If the car features

product, refer to the supplied manuals of both

a glass antenna, connect to the antenna booster

products and connect cords that have the same

power supply terminal.

function.

7 When not connecting a rear speaker lead to a Subwoofer

IP-BUS input (Blue)

This product

Front output

Subwoofer output or

non fading output

Antenna jack

Fuse (10 A)

Yellow/black

If you use an equipment with Mute function, wire this lead to

the Audio Mute lead on that equipment. If not, keep the Audio

Mute lead free of any connections.

Yellow

To terminal always supplied with power regardless of

ignition switch position.

Fig. 1

Red

To electric terminal controlled by ignition switch (12

V DC) ON/OFF.

Orange/white

To lighting switch terminal.

Black (ground)

To vehicle (metal) body.

With a 2 speaker system, do not connect

anything to the speaker leads that are not

connected to speakers.

Perform these connections when using the

optional amplifier.

Connecting cords with RCA pin

plugs (sold separately)

Rear output

15 cm (5-7/8 in.)

Jack for the Wired Remote Control Adaptors

Please see the Instruction Manual for the

Wired Remote Control Adaptors (sold separately).

Multi-CD player

(sold separately)

IP-BUS cable

Blue/white

To system control terminal of the power amp or

Auto-antenna relay control terminal (max. 300

mA 12 V DC).

System remote control

Front speaker

≠

White

Gray

Front speaker

≠

White/black

Gray/black

Left

Green

Violet

Rear speaker

≠

Green/black

Violet/black

Rear speaker

≠

Subwoofer

≠

Power amp

(sold separately)

Power amp

(sold separately)

Power amp

(sold separately)

Front speaker

Right

Rear speaker

Subwoofer

Fig. 2