- ページ 28
レシーバー Pioneer DVH-P4390UBのPDF オーナーズマニュアルをオンラインで閲覧またはダウンロードできます。Pioneer DVH-P4390UB 36 ページ。
ページを印刷するSection
Installation
05
DIN Rear-mount
1
Determine the appropriate position
where the holes on the bracket and the
side of the unit match.
2
Tighten two screws on each side.
3
1
2
1 Truss screw (5 mm × 8 mm)
2 Mounting bracket
3 Dashboard or console
Removing the unit
1
Remove the trim ring.
1 Trim ring
2 Notched tab
! Releasing the front panel allows easier ac-
cess to the trim ring.
! When reattaching the trim ring, point the
side with the notched tab down.
2
Insert the supplied extraction keys into
both sides of the unit until they click into
place.
54
En
3
Pull the unit out of the dashboard.
Removing and re-attaching the
front panel
You can remove the front panel to protect your
unit from theft.
For details, refer to Removing the front panel to
protect your unit from theft and Re-attaching
the front panel on page 9.
Additional Information
Troubleshooting
Common
Symptom
Cause
The power will not turn on.
Leads and connectors are incor-
The unit will not operate.
rectly connected.
The fuse is blown.
Noise and/or other factors are caus-
ing the built-in microprocessor to
operate incorrectly.
Operation with the remote con-
The remote control operation mode
trol is not possible.
is incorrect.
The unit does not operate cor-
Battery power is low.
rectly even when the appropriate
Some operations are prohibited
remote control buttons are
with certain discs.
pressed.
Playback is not possible.
The disc is dirty.
The type of disc loaded cannot be
played on this unit.
The disc loaded is not compatible
with this video system.
There is no sound.
Cables are not connected correctly.
The volume level will not rise.
The unit is performing still, slow mo-
tion or frame-by-frame playback.
The
icon is displayed, and op-
The operation is prohibited for the
eration is not possible.
disc.
The operation is not compatible
with the configuration of the disc.
The image displayed stops
The data could no longer be read
(pauses) and the unit cannot be
during playback.
operated.
There is no sound.
The volume level is low.
The volume level is low.
The attenuator is on.
The sound and video skip.
The unit is not firmly secured.
File size and transmission rate are
above recommended rates.
The aspect ratio is incorrect and
The aspect ratio setting is incorrect
the image is stretched.
for the display.
The motor sounds when the
The unit is confirming whether or
ignition switch is turned ON (or
not a disc is loaded.
is turned to ACC).
No xxxx appears when a dis-
There is no embedded text informa-
play is changed (No Title, for ex-
tion.
ample).
Appendix
Action (Reference page)
Confirm once more that all connections are
correct.
Rectify the cause and then replace the fuse.
Be sure to install a fuse with the same rating.
Turn the unit off and then on. (Page 9)
Switch to the correct remote control mode.
(Page 8)
Load a new battery.
Try operating with another disc.
Clean the disc. (Page 60)
Check the disc type.
Change the disc to one that is compatible
with your video system.
Connect the cables correctly.
There is no sound during still, slow motion or
frame-by-frame playback.
This operation is not possible.
This operation is not possible.
Stop playback once, and start playback again.
Adjust the volume level.
Turn the attenuator off.
Firmly secure the unit.
Create a DivX file that is within the recom-
mended size and transmission rate.
Select the appropriate setting for your display.
(Page 26)
This is a normal operation.
Switch the display or play another track/file.
55
En