- ページ 6

ステレオ・レシーバー Pioneer AVH-2330NEXのPDF インストレーション・マニュアルをオンラインで閲覧またはダウンロードできます。Pioneer AVH-2330NEX 25 ページ。 Dvd rds av receiver
Pioneer AVH-2330NEX にも：インストレーション・マニュアル (8 ページ)

ページを印刷する

Installation

Precautions before

installation

CAUTION

Never install this product in places where,

or in a manner that:

• Could injure the driver or passengers if

the vehicle stops suddenly.

• May interfere with the driver's operation

of the vehicle, such as on the floor in front

of the driver's seat, or close to the

steering wheel or shift lever.

• To ensure proper installation, be sure to

use the supplied parts in the manner

specified. If any parts are not supplied

with this product, use compatible parts in

the manner specified after you have the

part compatibility checked by your

dealer. If parts other than supplied or

compatible ones are used, they may

damage internal parts of this product or

they may work loose and the product

may become detached.

• Do not install this product where it may

(i) obstruct the driver's vision,

(ii) impair the performance of any of the

vehicle's operating systems or safety

features, including airbags, hazard lamp

buttons or

(iii) impair the driver's ability to safely

operate the vehicle.

• Never install this product in front of or

next to the place in the dashboard, door,

or pillar from which one of your vehicle's

airbags would deploy. Please refer to your

vehicle's owner's manual for reference to

the deployment area of the frontal

airbags.

Before installing

• Consult with your nearest dealer if

installation requires drilling holes or

other modifications of the vehicle.

• Before making a final installation of this

product, temporarily connect the wiring

to confirm that the connections are

correct and the system works properly.

Installation notes

• Do not install this product in places

subject to high temperatures or

humidity, such as:

– Places close to a heater, vent or air

conditioner.

– Places exposed to direct sunlight, such

as on top of the dashboard.

– Places that may be exposed to rain,

such as close to the door or on the

vehicle's floor.

• Install this product horizontally on a

surface within 0 to 30 degrees tolerance

(within 5 degrees to the left or right).

Improper installation of the unit with the

surface tilted more than these tolerances

increases the potential for errors in the

vehicle's location display, and might

otherwise cause reduced display

performance.

• When installing, to ensure proper heat

dispersal when using this product, make

sure you leave ample space behind the

rear panel and wrap any loose cables so

they are not blocking the vents.

5 cm

Leave ample

space

5 cm

Installation using the

screw holes on the side

of this product

Fastening this product to the factory

radio-mounting bracket.

Position this product so that its screw

holes are aligned with the screw holes

of the bracket, and tighten the screws at

three locations on each side.

Use either the truss head screws (5 mm

× 8 mm) or flush surface screws (5 mm ×

9 mm), depending on the shape of the

bracket's screw holes.

Factory radio-mounting bracket

If the pawl interferes with

installation, you may bend it down

out of the way.

Dashboard or console

Truss head screw or flush surface

screw

Be sure to use the screws supplied

with this product.

Installing the

microphone

• Install the microphone in a place where

its direction and distance from the driver

make it easiest to pick up the driver's

voice.

• Be sure to turn off (ACC OFF) the product

before connecting the microphone.

• Depending on the vehicle model, the

microphone cable length may be too

short when you mount the microphone

on the sun visor. In such cases, install the

microphone on the steering column.

Mounting on the sun

visor

Fit the microphone lead into the

groove.