- ページ 20

ステレオ・レシーバー Pioneer VSX-524-KのPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Pioneer VSX-524-K 40 ページ。 Av receiver
Pioneer VSX-524-K にも：取扱説明書 (38 ページ), 取扱説明書 (40 ページ), クイック・スタート・マニュアル (21 ページ), クイック・スタート・マニュアル (21 ページ)

ページを印刷する

Press

RECEIVER

on the remote control, then press the

HOME MENU

button.

The Home Menu appears on your TV. Use

on the remote control to navigate through the

ENTER

screens and select menu items. Press

the current menu.

•

Press

at any time to exit the Home

HOME MENU

Menu. If you cancel the Auto MCACC setup at any

time, the receiver automatically exits and no settings

will be made.

•

The screensaver automatically starts after three

minutes of inactivity.

Select 'Auto MCACC' from the Home Menu, then press

ENTER.

Ho m e M enu

1 .Auto MCACC

2.Manual SP Setup

3.Input Assign

4.Auto Power Down

5.HDMI Setup

Ret ur n

•

Mic In! blinks when the microphone is not connected

to MCACC SETUP MIC jack.

Try to be as quiet as possible after pressing ENTER. The

system outputs a series of test tones to establish the

ambient noise level.

Follow the instructions on-screen.

•

Make sure the microphone is connected.

•

Make sure the subwoofer is on and the volume is

turned up.

•

See below for notes regarding background noise and

other possible interference.

Wait for the test tones to finish.

A progress report is displayed on-screen while the

///

and

receiver outputs test tones to determine the speakers

present in your setup. Try to be as quiet as possible while

to exit

it's doing this.

RETURN

•

For correct speaker settings, do not adjust the volume

during the test tones.

Confirm the speaker configuration.

The configuration shown on-screen should reflect the

actual speakers you have.

•

With error messages (such as Too much ambient

noise) select RETRY after checking for ambient noise

(see

Other problems when using the Auto MCACC

setup

below).

If the speaker configuration displayed isn't correct, use

/

to select the speaker and

setting. When you're finished, go to the next step.

If you see an error message (ERR) in the right side

column, there may be a problem with the speaker

connection. If selecting RETRY doesn't fix the problem,

turn off the power and check the speaker connections.

1.Auto MCACC

Now Analyzing

Environment Check

Ambient Noise

Speaker YES/NO

Cancel

1.Auto MCACC

Check!

Front

[ YES ]

Center

[ YES ]

Surround

[ YES ]

Subwoofer

[ YES ]

10:Next

Return

/

to change the

Basic Setup (VSX-524 only)

Make sure 'OK' is selected, then press ENTER.

If the screen in step 8 is left untouched for 10 seconds

and

is not pressed in step 9, the Auto MCACC

ENTER

setup will start automatically as shown.

1.Auto MCACC

Now Analyzing

Surround Analyzing

Speaker System

X.Over

Speaker Distance

Channel Level

Acoustic Cal EQ

Return

A progress report is displayed on-screen while the

receiver outputs more test tones to determine the

optimum receiver settings for channel level, speaker

distance, and Acoustic Calibration EQ.

Again, try to be as quiet as possible while this is

happening. It may take 1 to 3 minutes.

The Auto MCACC setup has finished! You return to the

Home Menu.

The settings made in the Auto MCACC setup should give

you excellent surround sound from your system, but it is

also possible to adjust these settings manually using the

Home Menu (starting on

page

32).

Note

•

Depending on the characteristics of your room, sometimes

identical speakers with cone sizes of around 12 cm will end

up with different size settings. You can correct the setting

manually using the

Speaker Setting on page

•

The subwoofer distance setting may be farther than the

actual distance from the listening position. This setting

should be accurate (taking delay and room characteristics

into account) and generally does not need to be changed.

32.