- ページ 11

アンプ Pioneer A-307R A-209RのPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Pioneer A-307R A-209R 12 ページ。 Stereo amplifier
Pioneer A-307R A-209R にも：取扱説明書 (36 ページ), サービスマニュアル (33 ページ)

ページを印刷する

TROUBLESHOOTING

Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this component,

check the points below. Sometimes the trouble may lie in another component. Investigate the other components and electrical

appliances being used.

If the trouble cannot be rectified even after exercising the checks listed below, ask your nearest PIONEER authorized service center

or your dealer to carry out repair work.

Symptom

No power supplied to unit.

No sound.

No sound from one speaker.

Cannot record tapes.

Cannot perform tape copying.

The remote control unit does

not work. (Other components

cannot be operated.)

÷ Abnormal functioning of this unit may be caused by static electricity, or other external interference. To restore normal operation,

turn the power off and then on again, or unplug the AC power cord and then plug it in again.

Cause

÷ Power plug is disconnected from outlet.

÷ The amplifier's power plug has been

plugged into another component power

outlet (e.g. timer, etc.) but power to that

unit is disconnected.

÷ The AC INLET plug is disconnected.

÷ Connecting cords are disconnected from

terminals, or connected incorrectly.

÷ Terminals, or connecting cords pin plugs

are dirty.

÷ The TAPE2 MONITOR button is set to ON

(except when using an adaptor compo-

nent).

÷ Operation of other components is incor-

rect.

÷ The position of the INPUT SELECTOR does

not match the component to be played

back.

÷ Both SPEAKERS selector buttons are set

to OFF.

÷ Connecting cords or speaker cords are

disconnected on that side.

÷ BALANCE control is set to one side.

÷ Connections are incorrect.

÷ Operation of cassette deck is incorrect.

÷ The TAPE2 MONITOR button is set to ON.

÷ The position of the INPUT SELECTOR knob

and TAPE2 MONITOR button are incorrect

(when using 2 cassette decks).

÷ Operation of cassette decks is incorrect.

÷ Batteries are dead or no batteries in re-

mote control unit.

÷ The remote control sensor is not receiving

any signals.

÷ The remote control cord is not connected

correctly.

÷ A fluorescent light is shining on the remote

sensor window.

Remedy

÷ Insert plug securely into outlet.

÷ Turn on power to other component.

÷ Insert the AC INLET plug securely till the

bottom of the jack.

÷ Connect securely.

÷ Clean terminals and plugs.

÷ Set the TAPE2 MONITOR button to OFF.

÷ Consult the operating instructions for the

other components.

÷ Set the button correctly (CD, TUNER,

PHONO,LINE,TAPE1/MD(on the A-

307R),TAPE1/CD-R/MD(on the A-209R)).

÷ Set one button or both buttons to ON.

÷ Connect securely.

÷ Set BALANCE control to center position.

÷ Reconnect properly.

÷ Consult the operating instructions for the

cassette deck.

÷ Set the TAPE2 MONITOR button to OFF.

÷ Set buttons correctly (See section COPY-

ING TAPES).

÷ Consult the operating instructions for the

cassette decks.

÷ Insert new batteries (see page 5).

÷ Operate the remote control unit within a

range of 7 meters and an angle of 30

degrees (refer to page 5).

÷ Connect correctly (see page 5).

÷ Move so fluorescent light does not shine

directly on amplifier's front panel remote

sensor window.